Report: in output mode, with each command sent as soon as the prompt
arrives, a command right after "output" or "modulation" (e.g. "level -30"
after "output off", or "mode low input" after "output off" twice) got no
prompt and was dropped with "Command timeout" after 20 s; the next
command worked.
Cause: after a direct command the shell set operation_requested = true,
which is OP_LEVER. The sweep thread left sweep(), found no command yet,
and ui_process() handled that "lever event" and then set
operation_requested = OP_NONE. When the shell had parsed the next command
in between (shell_function set, OP_CONSOLE set), that clear wiped
OP_CONSOLE. A zero span output mode sweep only returns when
operation_requested is set, so the command never ran. Caught on hardware
with a breakpoint on the clear: operation_requested 0x05 with cmd_level /
cmd_mode waiting, every time.
- ui_process() clears only the bit it handled, locked, so OP_CONSOLE
survives lever and touch handling (a touch, e.g. a remote "touch" from
tinySA-App, hit the same clear).
- The sweep thread clears OP_CONSOLE together with taking shell_function,
which the shell sets together, so a request left by a direct or timed
out command does not keep aborting sweeps.
- A direct command asks for the sweep restart with OP_CONSOLE instead of
a fake lever event.
- SI4432_Listen() keeps OP_CONSOLE on entry, so a command ends listen
mode instead of being lost the same way.
Tested on a ZS405 (HW V0.4.5.1): both reported sequences 15 rounds each
without a hang (release firmware: 7 of 7 hung), every reply < 0.5 s.
In zero span output mode the sweep thread loop passes once per direct
command ("output off/on", "level") and not while idle. Remote touches
mixed with commands in output mode: 10 rounds without a hang. Input mode
touch menu and sweeping work. Listen mode and the jog lever not tested
on hardware. ULTRA +88 bytes, BASIC +84 bytes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Report: switching an Ultra (ZS405) on showed a momentary all white screen,
an Ultra+ (ZS406, ZS407) did not.
- The backlight came on before ili9341_init(), so the panel was lit in
reset and during its init; the ZS405 panel shows white then (the
ZS406/ZS407 panels, the ones with display inversion, stay black). It
now comes on at DEFAULT_BRIGHTNESS once the screen is cleared.
- That left a very brief flash: the backlight came on before the panel
had settled. The init now waits the 120 ms the controller needs after
SLEEP_OUT before DISPLAY_ON (LCD_WAKE_UP_MS). Only with
__LCD_BRIGHTNESS__: without backlight control a longer wait would
only show the uninitialised panel longer, so the BASIC is unchanged.
Tested on a ZS405 (HW V0.4.5.1) with the ST-Link: DAC2 at 0 darkens the
backlight, the backlight is dark with the CPU held in reset, the
backlight switched on 2 s after the init shows no flash, and with this
build power-ons show no flash. Start-up 120 ms longer; ULTRA +12 bytes,
BASIC binary unchanged in size.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Remote editing of a file name with tinySA-App became very slow after a
character or two, and the shell could end up not reading any input.
CMD_WAIT_MUTEX commands are run by the sweep thread, but while a keypad
is open that thread stays in ui_process_keypad() and never picks them
up, so the shell waited 4 x 5 s for each before "Command timeout". The
app polls vbat every 6 s outside live remote control, and every touch
queued behind those waits; local editing was not affected.
ui_process_keypad() now sets keypad_open while it waits for input, and
VNAShell_executeLine() answers a CMD_WAIT_MUTEX command with "keypad
active" instead of waiting, like "usb disk mode active". touch, release,
text, refresh, version and capture (CMD_RUN_IN_UI) run as before.
Tested on HW V0.4.5.1: with a keypad open vbat, pause and sweep answer
in 1 ms, capture rle and remote typing work, and after closing vbat and
sweep answer normally. tinySA-App clicking the screen without live
remote control (vbat polls every 6 s) typed all 8 characters, each poll
answered within 3 ms; before, the first poll stalled the rest.
Flash: ULTRA +44 bytes, BASIC +52.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
"refresh rle" is a third refresh mode next to off and on (auto_capture 2,
__REFRESH_RLE__). Plain "refresh on" is unchanged, so existing hosts keep
working; firmware without the mode answers "usage: refresh off|on".
- A bulk push of 256 pixels or more is sent as "rle8\r\n" + x, y, w, h,
u16 palette size + the region's own sorted palette, then the w * h
palette indices as one PackBits stream without lengths (DiSlord's
packbits(), 480 indices at a time). Background runs continue over the
rows. Smaller pushes fit the USB queue and stay "bulk", as do regions
with more than 256 colours or that might not get smaller.
- The waterfall scrolls the LCD as without remote desktop (4 lines at a
time) while remote_hold drops the pushes, then sends one "scrl\r\n" +
x, y, w, h + int16 dy instead of pushing every moved row again.
Tested on HW V0.5.4 (ZS407) with tinySA-App: the screen rebuilt from a
capture and all pushes equals a raw capture (0 pixels differ), every
stream is byte-identical to packbits(). Normal screen 289 -> 34 KB/s,
big waterfall 368 -> 23 KB/s at 2.12 instead of 1.75 sweeps/s.
Costs about 530 bytes of flash and 544 bytes of RAM.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
- 'reset dfu' and enter_dfu() are now also built for the tinySA4 (the
DFU menu stays tinySA3 only); the reply is sent before the reset
- F303 __early_init(): the jump to the system bootloader failed and the
bootloader reset the MCU. crt0 calls __early_init() on the process
stack with interrupts disabled, so switch to the main stack
(CONTROL = 0) and enable interrupts before the jump, as in the F072
board.c. Also enable the SYSCFG clock for the system memory remap and
replace the logical || that made it write 1 to SYSCFG_CFGR1
Tested on HW V0.4.5.1: 'reset dfu' enters the STM32 BOOTLOADER and
dfu-util can flash it.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
'capture' with any argument (tinySA-App sends 'capture rle') sends the
screen in the NanoVNA-D (DiSlord) RLE8 format: "BM", width, height,
bpp 8, compression 1, the palette, then per row the PackBits packed
palette indices. Plain 'capture' still sends raw RGB565.
The palette holds all colours the tinySA draws, so the screen is read
once: the LCD palette, the waterfall colours and the trace colours ORed
over each other and over the colours drawn before them in draw_cell().
The image viewer and the display test set capture_verify, as does a
colour not in the palette: the next capture then reads the screen twice
to add its colours, or sends raw when there are more than 256.
The screen is now read as one DMA stream (ili9341_read_memory_start /
next / end) so the next row is read while the current one is packed or
sent. Tested on HW V0.4.5.1, pixel exact against raw on normal, 4 trace,
waterfall, menu and keypad screens:
- capture rle: about 28 KB, 253 ms (was 482 ms raw)
- capture: 345 ms (was 482 ms)
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
STORAGE -> UPDATE FIRMWARE installs a firmware .bin from the SD card.
The shell command "fwupdate {file}" checks a file, "fwupdate {file} flash"
installs it. Config, calibration and presets (0x0803C000 and up) are never
touched; ROM DFU (jog held at power-on) stays the recovery.
- Image format: STM32F303xC.ld inlines the code rules to place a header
(magic, model, size, version) directly after the vector table and a
trailer (end magic, size, CRC field left unset) at the end of the image.
Only images with the header are accepted.
- Before anything is erased, the running firmware reads the whole file with
FatFs (page CRCs, image CRC, card sector map from FIL.clust) and reads it
again with the raw sector reader used by the update (dry run).
- The flasher runs from CCM RAM with interrupts off and VTOR in CCM. It keeps
page 0 in RAM, erases page 0 first and programs it last after a full image
CRC check, skips unchanged pages, retries errors without user input and
initializes the SD card again after it was removed or keeps failing.
It draws a progress bar and resets only after jog is released, because
jog pressed at reset starts the ROM bootloader.
The tinySA ULTRA now enumerates as a composite device: the CDC serial
port plus a mass storage interface (Bulk-Only Transport, SCSI). The SD
card is only presented to the PC in USB DISK mode (STORAGE menu or shell
command 'usbdisk on|off'), which stops sweeping and screen updates so the
mass storage thread owns SPI1 and spi_buffer. Outside the mode the PC
sees an empty card reader, so the serial port never re-enumerates. The
mode ends on touch, jog button, eject from the PC, card removal or
'usbdisk off'.
- usb_msc.c/h: mass storage thread, BOT state machine, SCSI commands
- usbcfg.c: composite descriptors (IAD, bcdDevice 0x0201), bulk EP3,
requests hook, packet memory reuse on a repeated SET_CONFIGURATION and
data toggle reset on CLEAR_FEATURE (both specific to this ChibiOS fork)
- ui.c: USB DISK menu item and mode screen
- main.c: 'usbdisk' command; shell commands that could use SPI1 are
refused while the mode is active
F072 builds are unchanged. Tested on HW V0.5.4 with Windows 11: about
620 KB/s read and 370 KB/s write, data verified against FatFs reads.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
- ChibiOS: send a zero length packet after any multiple of the bulk IN
packet size (backport from ChibiOS 21.11)
- halconf.h: name the serial buffer settings the way this ChibiOS fork
reads them (values equal to the defaults in use)
- shell_reset_console(): call the I-class queue functions locked
- VNAShell_executeLine(): enqueue the shell thread locked and only while
the command is still pending
- btn_wait_release(): wrap-safe repeat timing
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
The RTC backup checksum covers every byte except the checksum itself, including a reserved packed byte that was never assigned. Its stack value could therefore make otherwise valid state fail verification after reset.
Zero-initialize the complete backup image before assigning persisted fields so the checksum and reserved byte are deterministic.
It's now possible to save capture, traces, or both by clicking SD card icon
Disabling both options hides SD card icon
Config submenu was added to Storage menu, and all settings were moved there
Existing config remains valid, and default behavior with saving a capture is kept
Allow drag triggers
Fix Trigger level value on menu (if selected different unit format)
Fixed triggers lines in multi band mode if used different point count
Small fixes
erikkaashoek
PhysicistJohn
Shellever.IDX
Kevin Kettinger
alexey.lysiuk
DiSlord
Bohdan Kmit