You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

8.2 KiB

AMBEd

AMBEd is the transcoder daemon for XLXd. It converts voice between the digital modes on a reflector, using DVSI hardware for AMBE and software vocoders for Codec2 and IMBE. It also evens out levels, so stations sound alike whichever mode they use.

Version 1.5.0

Codecs

Codec Modes Vocoder
AMBE+ D-Star DVSI hardware
AMBE2+ DMR, YSF, NXDN DVSI hardware
Codec2 3200 bps M17 Software
IMBE P25 Software

DMR, YSF and NXDN share a codec, so voice between them isn't transcoded and AMBEd sees all three as DMR.

Transcoding paths

From To How
D-Star DMR/YSF/NXDN Hardware decode, hardware encode
DMR/YSF/NXDN D-Star Hardware decode, hardware encode
D-Star, DMR/YSF/NXDN M17, P25 Hardware decode, software encode
M17 D-Star, DMR/YSF/NXDN Software decode, hardware encode
M17 P25 Software decode, software encode
P25 D-Star, DMR/YSF/NXDN Software decode, hardware encode
P25 M17 Software decode, software encode

An M17 or P25 input uses 2 hardware channels, one for each AMBE encoder.

Hardware

  • DF2ET's AMBE3003USB
  • LX3JL's USB-3006
  • DVSI USB-3000, USB-3003 and USB-3012
  • NWDR ThumbDV and ThumbDV-3
  • DVMEGA AMBE3000 and AMBE3003
Device Hardware channels Transcoding channels Software vocoders (IMBE and Codec2)
3000 (pair) 2 2 1 each
3003 (single) 3 2 1 each
3003 (pair) 6 6 3 each
3003 + 3000 (pair) 4 4 2 each
3006 6 6 3 each
3012 12 12 6 each
  • USB-3000 devices must be used in pairs, or paired with a USB-3003.
  • Several devices can be used at once.
  • Avoid USB hubs, they can be unreliable.
  • The maximum number of concurrent streams is worked out from the hardware.

Installation

  1. Install the FTDI D2XX drivers from the FTDI website and follow their instructions. Tested on 1.4.6.

  2. Install the build tools:

    apt-get install build-essential
    
  3. Build and install:

    git clone https://github.com/LX3JL/xlxd.git
    cd xlxd/ambed
    make clean
    make
    make install
    

    This installs to /ambed. ambed.ini is only copied if there isn't one already, so your tuning is kept.

Always run make clean first after updating. The makefile doesn't track header changes, so a plain make can link old and new code together.

Running

ambed [ambed.ini]

Everything is set in ambed.ini. Set LISTEN_IP first: 127.0.0.1 if xlxd is on the same machine, otherwise the machine's own address. Without the file AMBEd uses the defaults in main.h and listens on 127.0.0.1.

AMBEd must run as root because of the FTDI driver, and the ftdi_sio and usbserial kernel modules must be unloaded. Plug in at least one device first.

To run it as a service, copy ../scripts/ambed.service to /etc/systemd/system/:

[Unit]
Description=AMBE Transcoder Daemon
After=network.target

[Service]
Type=simple
User=root
Group=root
ExecStartPre=-/sbin/rmmod ftdi_sio
ExecStartPre=-/sbin/rmmod usb_serial
ExecStart=/ambed/ambed /ambed/ambed.ini
Restart=on-abnormal

[Install]
WantedBy=multi-user.target

Then enable and start it:

systemctl daemon-reload
systemctl enable --now ambed

Or start it by hand with /ambed/run.

At startup AMBEd finds and configures every device, then reports:

Starting AMBEd 1.5.0
Codec interfaces initialized successfully : 6 channels available
Software vocoders : 3 IMBE (P25), 3 Codec2 (M17)
Max concurrent streams: 3 (from 6 vocoder channels)
AMBEd started and listening on 127.0.0.1:10100
Voice packets marked as DSCP 46

Audio processing

Every path runs through the same chain:

decode -> <MODE>_TO_PCM -> bandpass filter -> AGC -> PCM_TO_<MODE> -> encode
  • <MODE>_TO_PCM corrects what each mode's decoder does to the level, so every mode reaches the AGC at about the same level.
  • Bandpass filter keeps 300-3400 Hz.
  • AGC corrects what each station does to the level: mic gain, radio and voice.
  • PCM_TO_<MODE> sets the level for each encoder.

AGC

The AGC works like the one on an HF receiver: fast down, hold through gaps, then up, faster the further a station is below the target.

  • It follows the speech peaks, the loud parts of words, so it levels the speaker and leaves the shape of the speech alone for the vocoders.
  • Pauses and noise below AGC_GATE leave the gain where it is.
  • Each stream starts at 0 dB, so very short transmissions aren't fully levelled.
  • A peak limiter leaves room for the highest PCM_TO_<MODE>, so a boost can't clip an encoder.

Tuning

ambed.ini overrides the defaults in main.h without a rebuild. AMBEd checks it every 3 minutes. Most changes apply from the next stream, so a transmission already running keeps its levels, and DSCP changes apply at once. LISTEN_IP and LISTEN_PORT need a restart. A setting left out uses its default. A bad value is logged and ignored, and the value in use stays.

Setting Default Meaning
LISTEN_IP 127.0.0.1 IP to bind to
LISTEN_PORT 10100 UDP port, xlxd's TRANSCODER_PORT must match
DSCP_MARKING_ENABLE 1 Mark voice packets for QoS
DSCP_VALUE 46 DSCP value, 0-63, 46 is EF
STREAM_ACTIVITY_TIMEOUT 3 s Close a stream after this long with no packets
TUNING_LOG 1 Log levels when a stream closes
DSTAR_TO_PCM -10 dB D-Star decode gain
DMR_TO_PCM -1.5 dB DMR, YSF and NXDN decode gain
M17_TO_PCM -10.75 dB M17 decode gain
P25_TO_PCM -3.75 dB P25 decode gain
PCM_TO_DSTAR +11.5 dB D-Star encode gain
PCM_TO_DMR 0 dB DMR, YSF and NXDN encode gain
PCM_TO_M17 +5.25 dB M17 encode gain
PCM_TO_P25 +0.75 dB P25 encode gain
USE_AGC 1 AGC on or off
AGC_TARGET -41 dBFS Speech peak level to aim for
AGC_CLAMPING 9 dB Most the gain can move either way, 0 leaves the audio alone
AGC_ATTACK 150 ms How fast the gain comes down
AGC_HANG 1000 ms How long the gain holds before it can rise
AGC_RECOVERY 2 How fast the gain rises, dB/s for each dB below the target
AGC_RECOVERY_MIN 3 dB/s Slowest rise
AGC_RECOVERY_MAX 20 dB/s Fastest rise
AGC_GATE -60 dBFS Frames quieter than this don't move the gain
USE_BANDPASSFILTER 1 Bandpass filter on or off

Tuning log

When a stream closes, AMBEd logs the voice level at each stage. Pauses aren't counted, and a level is the mean absolute sample value. Set TUNING_LOG=0 to turn this off.

Tuning: stream 1 XLX672   M17 input, 440 voice frames of 540
Tuning:   decoded               level  -30.5 dBFS  peak   -8.9 dBFS  clipped 0.00%
Tuning:   M17_TO_PCM -10.75     level  -45.6 dBFS  peak  -19.9 dBFS  clipped 0.00%
Tuning:   AGC                   target -41.0 dBFS  speech peaks -43.6 dBFS  gain average -3.7 dB, -4.5 to +0.4 dB  at limit 0.0% high 0.0% low  limiter 0.00%
Tuning:   after AGC             level  -49.3 dBFS  peak  -23.7 dBFS  clipped 0.00%
Tuning:   PCM_TO_DSTAR +11.50   level  -37.8 dBFS  peak  -12.2 dBFS  clipped 0.00%
Tuning:   PCM_TO_DMR +0.00      level  -49.3 dBFS  peak  -23.7 dBFS  clipped 0.00%
Tuning:   PCM_TO_P25 +0.75      level  -48.5 dBFS  peak  -22.9 dBFS  clipped 0.00%

The callsign shown is the reflector's, as AMBEd isn't told who is talking.

How to tune

  1. Look at several stations on each mode, not just your own radio.
  2. Set each <MODE>_TO_PCM so typical stations on that mode average near 0 dB of AGC gain.
  3. If most modes sit high or low, move AGC_TARGET.
  4. A station at one limit for most of a stream is too far off for the AGC to correct.
  5. Use PCM_TO_<MODE> to match how each mode sounds on air, and back one off if it shows clipping.

To see levels without changing the audio, set AGC_CLAMPING=0. Speech peaks are still logged.

Build-time options

These are in main.h:

Setting Default Meaning
CONFIG_RELOAD_PERIOD 180 s How often ambed.ini is checked

License

Created by Jean-Luc Deltombe (LX3JL). AMBEd is part of xlxd, free software under the GNU General Public License v3 or later.

Powered by TurnKey Linux.