erikkaashoek
5 years ago
parent
7d6d1d33d0
commit
bef512d477
@ -0,0 +1,902 @@
|
|||||||
|
/*! @file radio_config.h
|
||||||
|
* @brief This file contains the automatically generated
|
||||||
|
* configurations.
|
||||||
|
*
|
||||||
|
* @n WDS GUI Version: 3.2.11.0
|
||||||
|
* @n Device: Si4468 Rev.: A2
|
||||||
|
*
|
||||||
|
* @b COPYRIGHT
|
||||||
|
* @n Silicon Laboratories Confidential
|
||||||
|
* @n Copyright 2017 Silicon Laboratories, Inc.
|
||||||
|
* @n http://www.silabs.com
|
||||||
|
*/
|
||||||
|
|
||||||
|
#ifndef RADIO_CONFIG_H_
|
||||||
|
#define RADIO_CONFIG_H_
|
||||||
|
|
||||||
|
// USER DEFINED PARAMETERS
|
||||||
|
// Define your own parameters here
|
||||||
|
|
||||||
|
// INPUT DATA
|
||||||
|
/*
|
||||||
|
// Crys_freq(Hz): 26000000 Crys_tol(ppm): 1 IF_mode: 2 High_perf_Ch_Fil: 1 OSRtune: 0 Ch_Fil_Bw_AFC: 0 ANT_DIV: 0 PM_pattern: 0
|
||||||
|
// MOD_type: 2 Rsymb(sps): 433333 Fdev(Hz): 1 RXBW(Hz): 850000 Manchester: 0 AFC_en: 0 Rsymb_error: 0.0 Chip-Version: 2
|
||||||
|
// RF Freq.(MHz): 978 API_TC: 29 fhst: 250000 inputBW: 1 BERT: 1 RAW_dout: 0 D_source: 1 Hi_pfm_div: 1
|
||||||
|
// API_ARR_Det_en: 0 Fdev_error: 0 API_ETSI: 2
|
||||||
|
//
|
||||||
|
// # RX IF frequency is -406250 Hz
|
||||||
|
// # WB filter 1 (BW = 793.61 kHz); NB-filter 1 (BW = 793.61 kHz)
|
||||||
|
//
|
||||||
|
// Modulation index: 0
|
||||||
|
*/
|
||||||
|
|
||||||
|
|
||||||
|
// CONFIGURATION PARAMETERS
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ 26000000L
|
||||||
|
#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER 0x00
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH 0x00
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP 0x03
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET 0xF000
|
||||||
|
|
||||||
|
|
||||||
|
// CONFIGURATION COMMANDS
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Command: RF_POWER_UP
|
||||||
|
// Description: Command to power-up the device and select the operational mode and functionality.
|
||||||
|
*/
|
||||||
|
#define RF_POWER_UP 0x02, 0x01, 0x00, 0x01, 0x8C, 0xBA, 0x80
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Command: RF_GPIO_PIN_CFG
|
||||||
|
// Description: Configures the GPIO pins.
|
||||||
|
*/
|
||||||
|
#define RF_GPIO_PIN_CFG 0x13, 0x08, 0x08, 0x0A, 0x21, 0x00, 0x00, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_GLOBAL_XO_TUNE_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x00
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x40,
|
||||||
|
// Descriptions:
|
||||||
|
// GLOBAL_XO_TUNE - Configure the internal capacitor frequency tuning bank for the crystal oscillator.
|
||||||
|
*/
|
||||||
|
#define RF_GLOBAL_XO_TUNE_1 0x11, 0x00, 0x01, 0x00, 0x52
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_GLOBAL_CONFIG_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x00
|
||||||
|
// Start ID: 0x03
|
||||||
|
// Default values: 0x20,
|
||||||
|
// Descriptions:
|
||||||
|
// GLOBAL_CONFIG - Global configuration settings.
|
||||||
|
*/
|
||||||
|
#define RF_GLOBAL_CONFIG_1 0x11, 0x00, 0x01, 0x03, 0x20
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_PREAMBLE_CONFIG_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x10
|
||||||
|
// Start ID: 0x04
|
||||||
|
// Default values: 0x21,
|
||||||
|
// Descriptions:
|
||||||
|
// PREAMBLE_CONFIG - General configuration bits for the Preamble field.
|
||||||
|
*/
|
||||||
|
#define RF_PREAMBLE_CONFIG_1 0x11, 0x10, 0x01, 0x04, 0x21
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_MOD_TYPE_12
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x02, 0x80, 0x07, 0x0F, 0x42, 0x40, 0x01, 0xC9, 0xC3, 0x80, 0x00, 0x06,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_MOD_TYPE - Selects the type of modulation. In TX mode, additionally selects the source of the modulation.
|
||||||
|
// MODEM_MAP_CONTROL - Controls polarity and mapping of transmit and receive bits.
|
||||||
|
// MODEM_DSM_CTRL - Miscellaneous control bits for the Delta-Sigma Modulator (DSM) in the PLL Synthesizer.
|
||||||
|
// MODEM_DATA_RATE_2 - Unsigned 24-bit value used to determine the TX data rate
|
||||||
|
// MODEM_DATA_RATE_1 - Unsigned 24-bit value used to determine the TX data rate
|
||||||
|
// MODEM_DATA_RATE_0 - Unsigned 24-bit value used to determine the TX data rate
|
||||||
|
// MODEM_TX_NCO_MODE_3 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_TX_NCO_MODE_2 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_TX_NCO_MODE_1 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_TX_NCO_MODE_0 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_FREQ_DEV_2 - 17-bit unsigned TX frequency deviation word.
|
||||||
|
// MODEM_FREQ_DEV_1 - 17-bit unsigned TX frequency deviation word.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_MOD_TYPE_12 0x11, 0x20, 0x0C, 0x00, 0x0B, 0x00, 0x07, 0x02, 0x71, 0x00, 0x05, 0x8C, 0xBA, 0x80, 0x00, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_FREQ_DEV_0_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x0C
|
||||||
|
// Default values: 0xD3,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_FREQ_DEV_0 - 17-bit unsigned TX frequency deviation word.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_FREQ_DEV_0_1 0x11, 0x20, 0x01, 0x0C, 0x28
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_TX_RAMP_DELAY_12
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x18
|
||||||
|
// Default values: 0x01, 0x00, 0x08, 0x03, 0xC0, 0x00, 0x10, 0x20, 0x00, 0x00, 0x00, 0x4B,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_TX_RAMP_DELAY - TX ramp-down delay setting.
|
||||||
|
// MODEM_MDM_CTRL - MDM control.
|
||||||
|
// MODEM_IF_CONTROL - Selects Fixed-IF, Scaled-IF, or Zero-IF mode of RX Modem operation.
|
||||||
|
// MODEM_IF_FREQ_2 - the IF frequency setting (an 18-bit signed number).
|
||||||
|
// MODEM_IF_FREQ_1 - the IF frequency setting (an 18-bit signed number).
|
||||||
|
// MODEM_IF_FREQ_0 - the IF frequency setting (an 18-bit signed number).
|
||||||
|
// MODEM_DECIMATION_CFG1 - Specifies three decimator ratios for the Cascaded Integrator Comb (CIC) filter.
|
||||||
|
// MODEM_DECIMATION_CFG0 - Specifies miscellaneous parameters and decimator ratios for the Cascaded Integrator Comb (CIC) filter.
|
||||||
|
// MODEM_DECIMATION_CFG2 - Specifies miscellaneous decimator filter selections.
|
||||||
|
// MODEM_IFPKD_THRESHOLDS -
|
||||||
|
// MODEM_BCR_OSR_1 - RX BCR/Slicer oversampling rate (12-bit unsigned number).
|
||||||
|
// MODEM_BCR_OSR_0 - RX BCR/Slicer oversampling rate (12-bit unsigned number).
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_TX_RAMP_DELAY_12 0x11, 0x20, 0x0C, 0x18, 0x01, 0x00, 0x0A, 0x03, 0xC0, 0x00, 0xB0, 0x10, 0x0C, 0xF9, 0x00, 0x44
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_BCR_NCO_OFFSET_2_12
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x24
|
||||||
|
// Default values: 0x06, 0xD3, 0xA0, 0x06, 0xD3, 0x02, 0xC0, 0x00, 0x00, 0x23, 0x83, 0x69,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_BCR_NCO_OFFSET_2 - RX BCR NCO offset value (an unsigned 22-bit number).
|
||||||
|
// MODEM_BCR_NCO_OFFSET_1 - RX BCR NCO offset value (an unsigned 22-bit number).
|
||||||
|
// MODEM_BCR_NCO_OFFSET_0 - RX BCR NCO offset value (an unsigned 22-bit number).
|
||||||
|
// MODEM_BCR_GAIN_1 - The unsigned 11-bit RX BCR loop gain value.
|
||||||
|
// MODEM_BCR_GAIN_0 - The unsigned 11-bit RX BCR loop gain value.
|
||||||
|
// MODEM_BCR_GEAR - RX BCR loop gear control.
|
||||||
|
// MODEM_BCR_MISC1 - Miscellaneous control bits for the RX BCR loop.
|
||||||
|
// MODEM_BCR_MISC0 - Miscellaneous RX BCR loop controls.
|
||||||
|
// MODEM_AFC_GEAR - RX AFC loop gear control.
|
||||||
|
// MODEM_AFC_WAIT - RX AFC loop wait time control.
|
||||||
|
// MODEM_AFC_GAIN_1 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality.
|
||||||
|
// MODEM_AFC_GAIN_0 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_BCR_NCO_OFFSET_2_12 0x11, 0x20, 0x0C, 0x24, 0x07, 0x8F, 0xD5, 0x00, 0x00, 0x02, 0xC0, 0x08, 0x00, 0x12, 0x00, 0x14
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_AFC_LIMITER_1_3
|
||||||
|
// Number of properties: 3
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x30
|
||||||
|
// Default values: 0x00, 0x40, 0xA0,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_AFC_LIMITER_1 - Set the AFC limiter value.
|
||||||
|
// MODEM_AFC_LIMITER_0 - Set the AFC limiter value.
|
||||||
|
// MODEM_AFC_MISC - Specifies miscellaneous AFC control bits.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_AFC_LIMITER_1_3 0x11, 0x20, 0x03, 0x30, 0x01, 0x7C, 0xA0
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_AGC_CONTROL_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x35
|
||||||
|
// Default values: 0xE0,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_AGC_CONTROL - Miscellaneous control bits for the Automatic Gain Control (AGC) function in the RX Chain.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_AGC_CONTROL_1 0x11, 0x20, 0x01, 0x35, 0xE0
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_AGC_WINDOW_SIZE_12
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x38
|
||||||
|
// Default values: 0x11, 0x10, 0x10, 0x0B, 0x1C, 0x40, 0x00, 0x00, 0x2B, 0x0C, 0xA4, 0x03,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_AGC_WINDOW_SIZE - Specifies the size of the measurement and settling windows for the AGC algorithm.
|
||||||
|
// MODEM_AGC_RFPD_DECAY - Sets the decay time of the RF peak detectors.
|
||||||
|
// MODEM_AGC_IFPD_DECAY - Sets the decay time of the IF peak detectors.
|
||||||
|
// MODEM_FSK4_GAIN1 - Specifies the gain factor of the secondary branch in 4(G)FSK ISI-suppression.
|
||||||
|
// MODEM_FSK4_GAIN0 - Specifies the gain factor of the primary branch in 4(G)FSK ISI-suppression.
|
||||||
|
// MODEM_FSK4_TH1 - 16 bit 4(G)FSK slicer threshold.
|
||||||
|
// MODEM_FSK4_TH0 - 16 bit 4(G)FSK slicer threshold.
|
||||||
|
// MODEM_FSK4_MAP - 4(G)FSK symbol mapping code.
|
||||||
|
// MODEM_OOK_PDTC - Configures the attack and decay times of the OOK Peak Detector.
|
||||||
|
// MODEM_OOK_BLOPK - Configures the slicing reference level of the OOK Peak Detector.
|
||||||
|
// MODEM_OOK_CNT1 - OOK control.
|
||||||
|
// MODEM_OOK_MISC - Selects the detector(s) used for demodulation of an OOK signal, or for demodulation of a (G)FSK signal when using the asynchronous demodulator.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_AGC_WINDOW_SIZE_12 0x11, 0x20, 0x0C, 0x38, 0x11, 0x0F, 0x0F, 0x80, 0x1A, 0x20, 0x00, 0x00, 0x28, 0x0C, 0xA4, 0x23
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_RAW_CONTROL_5
|
||||||
|
// Number of properties: 5
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x45
|
||||||
|
// Default values: 0x02, 0x00, 0xA3, 0x02, 0x80,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_RAW_CONTROL - Defines gain and enable controls for raw / nonstandard mode.
|
||||||
|
// MODEM_RAW_EYE_1 - 11 bit eye-open detector threshold.
|
||||||
|
// MODEM_RAW_EYE_0 - 11 bit eye-open detector threshold.
|
||||||
|
// MODEM_ANT_DIV_MODE - Antenna diversity mode settings.
|
||||||
|
// MODEM_ANT_DIV_CONTROL - Specifies controls for the Antenna Diversity algorithm.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_RAW_CONTROL_5 0x11, 0x20, 0x05, 0x45, 0x03, 0x00, 0x99, 0x01, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_RSSI_JUMP_THRESH_4
|
||||||
|
// Number of properties: 4
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x4B
|
||||||
|
// Default values: 0x0C, 0x01, 0x00, 0x40,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_RSSI_JUMP_THRESH - Configures the RSSI Jump Detection threshold.
|
||||||
|
// MODEM_RSSI_CONTROL - Control of the averaging modes and latching time for reporting RSSI value(s).
|
||||||
|
// MODEM_RSSI_CONTROL2 - RSSI Jump Detection control.
|
||||||
|
// MODEM_RSSI_COMP - RSSI compensation value.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_RSSI_JUMP_THRESH_4 0x11, 0x20, 0x04, 0x4B, 0x06, 0x09, 0x10, 0x40
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_RAW_SEARCH2_2
|
||||||
|
// Number of properties: 2
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x50
|
||||||
|
// Default values: 0x00, 0x08,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_RAW_SEARCH2 - Defines and controls the search period length for the Moving Average and Min-Max detectors.
|
||||||
|
// MODEM_CLKGEN_BAND - Select PLL Synthesizer output divider ratio as a function of frequency band.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_RAW_SEARCH2_2 0x11, 0x20, 0x02, 0x50, 0x94, 0x08
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_SPIKE_DET_2
|
||||||
|
// Number of properties: 2
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x54
|
||||||
|
// Default values: 0x00, 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_SPIKE_DET - Configures the threshold for (G)FSK Spike Detection.
|
||||||
|
// MODEM_ONE_SHOT_AFC - Configures parameters for th e One Shot AFC function and for BCR timing/acquisition.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_SPIKE_DET_2 0x11, 0x20, 0x02, 0x54, 0x03, 0x07
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_RSSI_MUTE_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x57
|
||||||
|
// Default values: 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_RSSI_MUTE - Configures muting of the RSSI to avoid false RSSI interrupts.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_RSSI_MUTE_1 0x11, 0x20, 0x01, 0x57, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_DSA_CTRL1_5
|
||||||
|
// Number of properties: 5
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x5B
|
||||||
|
// Default values: 0x00, 0x00, 0x00, 0x00, 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_DSA_CTRL1 - Configures parameters for the Signal Arrival Detection circuit block and algorithm.
|
||||||
|
// MODEM_DSA_CTRL2 - Configures parameters for the Signal Arrival Detection circuit block and algorithm.
|
||||||
|
// MODEM_DSA_QUAL - Configures parameters for the Eye Opening qualification m ethod of the Signal Arrival Detection algorithm.
|
||||||
|
// MODEM_DSA_RSSI - Signal Arrival Detect RSSI Qualifier Config
|
||||||
|
// MODEM_DSA_MISC - Miscellaneous detection of signal arrival bits.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_DSA_CTRL1_5 0x11, 0x20, 0x05, 0x5B, 0x40, 0x04, 0x04, 0x78, 0x20
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x21
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE13_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE12_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE11_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE10_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE9_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE8_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE7_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE6_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE5_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE4_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE3_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE2_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12 0x11, 0x21, 0x0C, 0x00, 0xCC, 0xA1, 0x30, 0xA0, 0x21, 0xD1, 0xB9, 0xC9, 0xEA, 0x05, 0x12, 0x11
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x21
|
||||||
|
// Start ID: 0x0C
|
||||||
|
// Default values: 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F, 0xFF, 0xC4, 0x30, 0x7F, 0xF5, 0xB5,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE1_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE0_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM1 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM2 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM3 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE13_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE12_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE11_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE10_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE9_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE8_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12 0x11, 0x21, 0x0C, 0x0C, 0x0A, 0x04, 0x15, 0xFC, 0x03, 0x00, 0xCC, 0xA1, 0x30, 0xA0, 0x21, 0xD1
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x21
|
||||||
|
// Start ID: 0x18
|
||||||
|
// Default values: 0xB8, 0xDE, 0x05, 0x17, 0x16, 0x0C, 0x03, 0x00, 0x15, 0xFF, 0x00, 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE7_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE6_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE5_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE4_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE3_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE2_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE1_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE0_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM1 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM2 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM3 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12 0x11, 0x21, 0x0C, 0x18, 0xB9, 0xC9, 0xEA, 0x05, 0x12, 0x11, 0x0A, 0x04, 0x15, 0xFC, 0x03, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_PA_TC_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x22
|
||||||
|
// Start ID: 0x03
|
||||||
|
// Default values: 0x5D,
|
||||||
|
// Descriptions:
|
||||||
|
// PA_TC - Configuration of PA ramping parameters.
|
||||||
|
*/
|
||||||
|
#define RF_PA_TC_1 0x11, 0x22, 0x01, 0x03, 0x1D
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_SYNTH_PFDCP_CPFF_7
|
||||||
|
// Number of properties: 7
|
||||||
|
// Group ID: 0x23
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x2C, 0x0E, 0x0B, 0x04, 0x0C, 0x73, 0x03,
|
||||||
|
// Descriptions:
|
||||||
|
// SYNTH_PFDCP_CPFF - Feed forward charge pump current selection.
|
||||||
|
// SYNTH_PFDCP_CPINT - Integration charge pump current selection.
|
||||||
|
// SYNTH_VCO_KV - Gain scaling factors (Kv) for the VCO tuning varactors on both the integrated-path and feed forward path.
|
||||||
|
// SYNTH_LPFILT3 - Value of resistor R2 in feed-forward path of loop filter.
|
||||||
|
// SYNTH_LPFILT2 - Value of capacitor C2 in feed-forward path of loop filter.
|
||||||
|
// SYNTH_LPFILT1 - Value of capacitors C1 and C3 in feed-forward path of loop filter.
|
||||||
|
// SYNTH_LPFILT0 - Bias current of the active amplifier in the feed-forward loop filter.
|
||||||
|
*/
|
||||||
|
#define RF_SYNTH_PFDCP_CPFF_7 0x11, 0x23, 0x07, 0x00, 0x2C, 0x0E, 0x0B, 0x04, 0x0C, 0x73, 0x03
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_FREQ_CONTROL_INTE_8
|
||||||
|
// Number of properties: 8
|
||||||
|
// Group ID: 0x40
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x3C, 0x08, 0x00, 0x00, 0x00, 0x00, 0x20, 0xFF,
|
||||||
|
// Descriptions:
|
||||||
|
// FREQ_CONTROL_INTE - Frac-N PLL Synthesizer integer divide number.
|
||||||
|
// FREQ_CONTROL_FRAC_2 - Frac-N PLL fraction number.
|
||||||
|
// FREQ_CONTROL_FRAC_1 - Frac-N PLL fraction number.
|
||||||
|
// FREQ_CONTROL_FRAC_0 - Frac-N PLL fraction number.
|
||||||
|
// FREQ_CONTROL_CHANNEL_STEP_SIZE_1 - EZ Frequency Programming channel step size.
|
||||||
|
// FREQ_CONTROL_CHANNEL_STEP_SIZE_0 - EZ Frequency Programming channel step size.
|
||||||
|
// FREQ_CONTROL_W_SIZE - Set window gating period (in number of crystal reference clock cycles) for counting VCO frequency during calibration.
|
||||||
|
// FREQ_CONTROL_VCOCNT_RX_ADJ - Adjust target count for VCO calibration in RX mode.
|
||||||
|
*/
|
||||||
|
#define RF_FREQ_CONTROL_INTE_8 0x11, 0x40, 0x08, 0x00, 0x4B, 0x08, 0x80, 0x00, 0x27, 0x62, 0x20, 0xFF
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Command: RF_START_RX
|
||||||
|
// Description: Switches to RX state and starts reception of a packet.
|
||||||
|
*/
|
||||||
|
#define RF_START_RX 0x32, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Command: RF_IRCAL
|
||||||
|
// Description: Image rejection calibration.
|
||||||
|
*/
|
||||||
|
#define RF_IRCAL 0x17, 0x56, 0x10, 0xFA, 0xF0
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Command: RF_IRCAL_1
|
||||||
|
// Description: Image rejection calibration.
|
||||||
|
*/
|
||||||
|
#define RF_IRCAL_1 0x17, 0x13, 0x10, 0xFA, 0xF0
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_GLOBAL_CLK_CFG_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x00
|
||||||
|
// Start ID: 0x01
|
||||||
|
// Default values: 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// GLOBAL_CLK_CFG - Clock configuration options.
|
||||||
|
*/
|
||||||
|
#define RF_GLOBAL_CLK_CFG_1 0x11, 0x00, 0x01, 0x01, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_GLOBAL_CONFIG_1_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x00
|
||||||
|
// Start ID: 0x03
|
||||||
|
// Default values: 0x20,
|
||||||
|
// Descriptions:
|
||||||
|
// GLOBAL_CONFIG - Global configuration settings.
|
||||||
|
*/
|
||||||
|
#define RF_GLOBAL_CONFIG_1_1 0x11, 0x00, 0x01, 0x03, 0x20
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_INT_CTL_ENABLE_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x01
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x04,
|
||||||
|
// Descriptions:
|
||||||
|
// INT_CTL_ENABLE - This property provides for global enabling of the three interrupt groups (Chip, Modem and Packet Handler) in order to generate HW interrupts at the NIRQ pin.
|
||||||
|
*/
|
||||||
|
#define RF_INT_CTL_ENABLE_1 0x11, 0x01, 0x01, 0x00, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_FRR_CTL_A_MODE_4
|
||||||
|
// Number of properties: 4
|
||||||
|
// Group ID: 0x02
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x01, 0x02, 0x09, 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// FRR_CTL_A_MODE - Fast Response Register A Configuration.
|
||||||
|
// FRR_CTL_B_MODE - Fast Response Register B Configuration.
|
||||||
|
// FRR_CTL_C_MODE - Fast Response Register C Configuration.
|
||||||
|
// FRR_CTL_D_MODE - Fast Response Register D Configuration.
|
||||||
|
*/
|
||||||
|
#define RF_FRR_CTL_A_MODE_4 0x11, 0x02, 0x04, 0x00, 0x05, 0x01, 0x07, 0x09
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_PREAMBLE_CONFIG_STD_1_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x10
|
||||||
|
// Start ID: 0x01
|
||||||
|
// Default values: 0x14,
|
||||||
|
// Descriptions:
|
||||||
|
// PREAMBLE_CONFIG_STD_1 - Configuration of reception of a packet with a Standard Preamble pattern.
|
||||||
|
*/
|
||||||
|
#define RF_PREAMBLE_CONFIG_STD_1_1 0x11, 0x10, 0x01, 0x01, 0x88
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_PKT_CONFIG1_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x12
|
||||||
|
// Start ID: 0x06
|
||||||
|
// Default values: 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// PKT_CONFIG1 - General configuration bits for transmission or reception of a packet.
|
||||||
|
*/
|
||||||
|
#define RF_PKT_CONFIG1_1 0x11, 0x12, 0x01, 0x06, 0x40
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_MOD_TYPE_12_1
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x02, 0x80, 0x07, 0x0F, 0x42, 0x40, 0x01, 0xC9, 0xC3, 0x80, 0x00, 0x06,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_MOD_TYPE - Selects the type of modulation. In TX mode, additionally selects the source of the modulation.
|
||||||
|
// MODEM_MAP_CONTROL - Controls polarity and mapping of transmit and receive bits.
|
||||||
|
// MODEM_DSM_CTRL - Miscellaneous control bits for the Delta-Sigma Modulator (DSM) in the PLL Synthesizer.
|
||||||
|
// MODEM_DATA_RATE_2 - Unsigned 24-bit value used to determine the TX data rate
|
||||||
|
// MODEM_DATA_RATE_1 - Unsigned 24-bit value used to determine the TX data rate
|
||||||
|
// MODEM_DATA_RATE_0 - Unsigned 24-bit value used to determine the TX data rate
|
||||||
|
// MODEM_TX_NCO_MODE_3 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_TX_NCO_MODE_2 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_TX_NCO_MODE_1 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_TX_NCO_MODE_0 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
|
||||||
|
// MODEM_FREQ_DEV_2 - 17-bit unsigned TX frequency deviation word.
|
||||||
|
// MODEM_FREQ_DEV_1 - 17-bit unsigned TX frequency deviation word.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_MOD_TYPE_12_1 0x11, 0x20, 0x0C, 0x00, 0x0A, 0x00, 0x07, 0x42, 0x1F, 0x12, 0x01, 0x8C, 0xBA, 0x80, 0x00, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_FREQ_DEV_0_1_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x0C
|
||||||
|
// Default values: 0xD3,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_FREQ_DEV_0 - 17-bit unsigned TX frequency deviation word.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_FREQ_DEV_0_1_1 0x11, 0x20, 0x01, 0x0C, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_TX_RAMP_DELAY_12_1
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x18
|
||||||
|
// Default values: 0x01, 0x00, 0x08, 0x03, 0xC0, 0x00, 0x10, 0x20, 0x00, 0x00, 0x00, 0x4B,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_TX_RAMP_DELAY - TX ramp-down delay setting.
|
||||||
|
// MODEM_MDM_CTRL - MDM control.
|
||||||
|
// MODEM_IF_CONTROL - Selects Fixed-IF, Scaled-IF, or Zero-IF mode of RX Modem operation.
|
||||||
|
// MODEM_IF_FREQ_2 - the IF frequency setting (an 18-bit signed number).
|
||||||
|
// MODEM_IF_FREQ_1 - the IF frequency setting (an 18-bit signed number).
|
||||||
|
// MODEM_IF_FREQ_0 - the IF frequency setting (an 18-bit signed number).
|
||||||
|
// MODEM_DECIMATION_CFG1 - Specifies three decimator ratios for the Cascaded Integrator Comb (CIC) filter.
|
||||||
|
// MODEM_DECIMATION_CFG0 - Specifies miscellaneous parameters and decimator ratios for the Cascaded Integrator Comb (CIC) filter.
|
||||||
|
// MODEM_DECIMATION_CFG2 - Specifies miscellaneous decimator filter selections.
|
||||||
|
// MODEM_IFPKD_THRESHOLDS -
|
||||||
|
// MODEM_BCR_OSR_1 - RX BCR/Slicer oversampling rate (12-bit unsigned number).
|
||||||
|
// MODEM_BCR_OSR_0 - RX BCR/Slicer oversampling rate (12-bit unsigned number).
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_TX_RAMP_DELAY_12_1 0x11, 0x20, 0x0C, 0x18, 0x01, 0x00, 0x0A, 0x03, 0xC0, 0x00, 0x00, 0x30, 0x00, 0xF9, 0x00, 0x3C
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_BCR_NCO_OFFSET_2_12_1
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x24
|
||||||
|
// Default values: 0x06, 0xD3, 0xA0, 0x06, 0xD3, 0x02, 0xC0, 0x00, 0x00, 0x23, 0x83, 0x69,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_BCR_NCO_OFFSET_2 - RX BCR NCO offset value (an unsigned 22-bit number).
|
||||||
|
// MODEM_BCR_NCO_OFFSET_1 - RX BCR NCO offset value (an unsigned 22-bit number).
|
||||||
|
// MODEM_BCR_NCO_OFFSET_0 - RX BCR NCO offset value (an unsigned 22-bit number).
|
||||||
|
// MODEM_BCR_GAIN_1 - The unsigned 11-bit RX BCR loop gain value.
|
||||||
|
// MODEM_BCR_GAIN_0 - The unsigned 11-bit RX BCR loop gain value.
|
||||||
|
// MODEM_BCR_GEAR - RX BCR loop gear control.
|
||||||
|
// MODEM_BCR_MISC1 - Miscellaneous control bits for the RX BCR loop.
|
||||||
|
// MODEM_BCR_MISC0 - Miscellaneous RX BCR loop controls.
|
||||||
|
// MODEM_AFC_GEAR - RX AFC loop gear control.
|
||||||
|
// MODEM_AFC_WAIT - RX AFC loop wait time control.
|
||||||
|
// MODEM_AFC_GAIN_1 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality.
|
||||||
|
// MODEM_AFC_GAIN_0 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_BCR_NCO_OFFSET_2_12_1 0x11, 0x20, 0x0C, 0x24, 0x08, 0x88, 0x88, 0x07, 0xFF, 0x02, 0xC0, 0x08, 0x00, 0x23, 0x08, 0x89
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_AFC_LIMITER_1_3_1
|
||||||
|
// Number of properties: 3
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x30
|
||||||
|
// Default values: 0x00, 0x40, 0xA0,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_AFC_LIMITER_1 - Set the AFC limiter value.
|
||||||
|
// MODEM_AFC_LIMITER_0 - Set the AFC limiter value.
|
||||||
|
// MODEM_AFC_MISC - Specifies miscellaneous AFC control bits.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_AFC_LIMITER_1_3_1 0x11, 0x20, 0x03, 0x30, 0x01, 0x92, 0xA0
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_AGC_CONTROL_1_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x35
|
||||||
|
// Default values: 0xE0,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_AGC_CONTROL - Miscellaneous control bits for the Automatic Gain Control (AGC) function in the RX Chain.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_AGC_CONTROL_1_1 0x11, 0x20, 0x01, 0x35, 0xE2
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_AGC_WINDOW_SIZE_12_1
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x38
|
||||||
|
// Default values: 0x11, 0x10, 0x10, 0x0B, 0x1C, 0x40, 0x00, 0x00, 0x2B, 0x0C, 0xA4, 0x03,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_AGC_WINDOW_SIZE - Specifies the size of the measurement and settling windows for the AGC algorithm.
|
||||||
|
// MODEM_AGC_RFPD_DECAY - Sets the decay time of the RF peak detectors.
|
||||||
|
// MODEM_AGC_IFPD_DECAY - Sets the decay time of the IF peak detectors.
|
||||||
|
// MODEM_FSK4_GAIN1 - Specifies the gain factor of the secondary branch in 4(G)FSK ISI-suppression.
|
||||||
|
// MODEM_FSK4_GAIN0 - Specifies the gain factor of the primary branch in 4(G)FSK ISI-suppression.
|
||||||
|
// MODEM_FSK4_TH1 - 16 bit 4(G)FSK slicer threshold.
|
||||||
|
// MODEM_FSK4_TH0 - 16 bit 4(G)FSK slicer threshold.
|
||||||
|
// MODEM_FSK4_MAP - 4(G)FSK symbol mapping code.
|
||||||
|
// MODEM_OOK_PDTC - Configures the attack and decay times of the OOK Peak Detector.
|
||||||
|
// MODEM_OOK_BLOPK - Configures the slicing reference level of the OOK Peak Detector.
|
||||||
|
// MODEM_OOK_CNT1 - OOK control.
|
||||||
|
// MODEM_OOK_MISC - Selects the detector(s) used for demodulation of an OOK signal, or for demodulation of a (G)FSK signal when using the asynchronous demodulator.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_AGC_WINDOW_SIZE_12_1 0x11, 0x20, 0x0C, 0x38, 0x21, 0x09, 0x09, 0x80, 0x02, 0x00, 0x00, 0x00, 0x27, 0x0C, 0xA4, 0x23
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_RAW_CONTROL_10
|
||||||
|
// Number of properties: 10
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x45
|
||||||
|
// Default values: 0x02, 0x00, 0xA3, 0x02, 0x80, 0xFF, 0x0C, 0x01, 0x00, 0x40,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_RAW_CONTROL - Defines gain and enable controls for raw / nonstandard mode.
|
||||||
|
// MODEM_RAW_EYE_1 - 11 bit eye-open detector threshold.
|
||||||
|
// MODEM_RAW_EYE_0 - 11 bit eye-open detector threshold.
|
||||||
|
// MODEM_ANT_DIV_MODE - Antenna diversity mode settings.
|
||||||
|
// MODEM_ANT_DIV_CONTROL - Specifies controls for the Antenna Diversity algorithm.
|
||||||
|
// MODEM_RSSI_THRESH - Configures the RSSI threshold.
|
||||||
|
// MODEM_RSSI_JUMP_THRESH - Configures the RSSI Jump Detection threshold.
|
||||||
|
// MODEM_RSSI_CONTROL - Control of the averaging modes and latching time for reporting RSSI value(s).
|
||||||
|
// MODEM_RSSI_CONTROL2 - RSSI Jump Detection control.
|
||||||
|
// MODEM_RSSI_COMP - RSSI compensation value.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_RAW_CONTROL_10 0x11, 0x20, 0x0A, 0x45, 0x03, 0x00, 0x00, 0x01, 0x00, 0xFF, 0x08, 0x10, 0x10, 0x40
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_RAW_SEARCH2_2_1
|
||||||
|
// Number of properties: 2
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x50
|
||||||
|
// Default values: 0x00, 0x08,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_RAW_SEARCH2 - Defines and controls the search period length for the Moving Average and Min-Max detectors.
|
||||||
|
// MODEM_CLKGEN_BAND - Select PLL Synthesizer output divider ratio as a function of frequency band.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_RAW_SEARCH2_2_1 0x11, 0x20, 0x02, 0x50, 0x94, 0x08
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_SPIKE_DET_2_1
|
||||||
|
// Number of properties: 2
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x54
|
||||||
|
// Default values: 0x00, 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_SPIKE_DET - Configures the threshold for (G)FSK Spike Detection.
|
||||||
|
// MODEM_ONE_SHOT_AFC - Configures parameters for th e One Shot AFC function and for BCR timing/acquisition.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_SPIKE_DET_2_1 0x11, 0x20, 0x02, 0x54, 0x03, 0x07
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_RSSI_MUTE_1_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x57
|
||||||
|
// Default values: 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_RSSI_MUTE - Configures muting of the RSSI to avoid false RSSI interrupts.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_RSSI_MUTE_1_1 0x11, 0x20, 0x01, 0x57, 0x00
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_DSA_CTRL1_5_1
|
||||||
|
// Number of properties: 5
|
||||||
|
// Group ID: 0x20
|
||||||
|
// Start ID: 0x5B
|
||||||
|
// Default values: 0x00, 0x00, 0x00, 0x00, 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_DSA_CTRL1 - Configures parameters for the Signal Arrival Detection circuit block and algorithm.
|
||||||
|
// MODEM_DSA_CTRL2 - Configures parameters for the Signal Arrival Detection circuit block and algorithm.
|
||||||
|
// MODEM_DSA_QUAL - Configures parameters for the Eye Opening qualification m ethod of the Signal Arrival Detection algorithm.
|
||||||
|
// MODEM_DSA_RSSI - Signal Arrival Detect RSSI Qualifier Config
|
||||||
|
// MODEM_DSA_MISC - Miscellaneous detection of signal arrival bits.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_DSA_CTRL1_5_1 0x11, 0x20, 0x05, 0x5B, 0x40, 0x04, 0x01, 0x78, 0x20
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12_1
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x21
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE13_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE12_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE11_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE10_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE9_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE8_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE7_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE6_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE5_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE4_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE3_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE2_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12_1 0x11, 0x21, 0x0C, 0x00, 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12_1
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x21
|
||||||
|
// Start ID: 0x0C
|
||||||
|
// Default values: 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F, 0xFF, 0xC4, 0x30, 0x7F, 0xF5, 0xB5,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE1_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COE0_7_0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM0 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM1 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM2 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX1_CHFLT_COEM3 - Filter coefficients for the first set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE13_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE12_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE11_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE10_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE9_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE8_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12_1 0x11, 0x21, 0x0C, 0x0C, 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F, 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12_1
|
||||||
|
// Number of properties: 12
|
||||||
|
// Group ID: 0x21
|
||||||
|
// Start ID: 0x18
|
||||||
|
// Default values: 0xB8, 0xDE, 0x05, 0x17, 0x16, 0x0C, 0x03, 0x00, 0x15, 0xFF, 0x00, 0x00,
|
||||||
|
// Descriptions:
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE7_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE6_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE5_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE4_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE3_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE2_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE1_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COE0_7_0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM0 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM1 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM2 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
// MODEM_CHFLT_RX2_CHFLT_COEM3 - Filter coefficients for the second set of RX filter coefficients.
|
||||||
|
*/
|
||||||
|
#define RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12_1 0x11, 0x21, 0x0C, 0x18, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01, 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_PA_TC_1_1
|
||||||
|
// Number of properties: 1
|
||||||
|
// Group ID: 0x22
|
||||||
|
// Start ID: 0x03
|
||||||
|
// Default values: 0x5D,
|
||||||
|
// Descriptions:
|
||||||
|
// PA_TC - Configuration of PA ramping parameters.
|
||||||
|
*/
|
||||||
|
#define RF_PA_TC_1_1 0x11, 0x22, 0x01, 0x03, 0x5D
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_SYNTH_PFDCP_CPFF_7_1
|
||||||
|
// Number of properties: 7
|
||||||
|
// Group ID: 0x23
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x2C, 0x0E, 0x0B, 0x04, 0x0C, 0x73, 0x03,
|
||||||
|
// Descriptions:
|
||||||
|
// SYNTH_PFDCP_CPFF - Feed forward charge pump current selection.
|
||||||
|
// SYNTH_PFDCP_CPINT - Integration charge pump current selection.
|
||||||
|
// SYNTH_VCO_KV - Gain scaling factors (Kv) for the VCO tuning varactors on both the integrated-path and feed forward path.
|
||||||
|
// SYNTH_LPFILT3 - Value of resistor R2 in feed-forward path of loop filter.
|
||||||
|
// SYNTH_LPFILT2 - Value of capacitor C2 in feed-forward path of loop filter.
|
||||||
|
// SYNTH_LPFILT1 - Value of capacitors C1 and C3 in feed-forward path of loop filter.
|
||||||
|
// SYNTH_LPFILT0 - Bias current of the active amplifier in the feed-forward loop filter.
|
||||||
|
*/
|
||||||
|
#define RF_SYNTH_PFDCP_CPFF_7_1 0x11, 0x23, 0x07, 0x00, 0x01, 0x05, 0x0B, 0x05, 0x02, 0x00, 0x03
|
||||||
|
|
||||||
|
/*
|
||||||
|
// Set properties: RF_FREQ_CONTROL_INTE_8_1
|
||||||
|
// Number of properties: 8
|
||||||
|
// Group ID: 0x40
|
||||||
|
// Start ID: 0x00
|
||||||
|
// Default values: 0x3C, 0x08, 0x00, 0x00, 0x00, 0x00, 0x20, 0xFF,
|
||||||
|
// Descriptions:
|
||||||
|
// FREQ_CONTROL_INTE - Frac-N PLL Synthesizer integer divide number.
|
||||||
|
// FREQ_CONTROL_FRAC_2 - Frac-N PLL fraction number.
|
||||||
|
// FREQ_CONTROL_FRAC_1 - Frac-N PLL fraction number.
|
||||||
|
// FREQ_CONTROL_FRAC_0 - Frac-N PLL fraction number.
|
||||||
|
// FREQ_CONTROL_CHANNEL_STEP_SIZE_1 - EZ Frequency Programming channel step size.
|
||||||
|
// FREQ_CONTROL_CHANNEL_STEP_SIZE_0 - EZ Frequency Programming channel step size.
|
||||||
|
// FREQ_CONTROL_W_SIZE - Set window gating period (in number of crystal reference clock cycles) for counting VCO frequency during calibration.
|
||||||
|
// FREQ_CONTROL_VCOCNT_RX_ADJ - Adjust target count for VCO calibration in RX mode.
|
||||||
|
*/
|
||||||
|
#define RF_FREQ_CONTROL_INTE_8_1 0x11, 0x40, 0x08, 0x00, 0x4A, 0x09, 0xD8, 0x9D, 0x27, 0x62, 0x20, 0xFF
|
||||||
|
|
||||||
|
|
||||||
|
// AUTOMATICALLY GENERATED CODE!
|
||||||
|
// DO NOT EDIT/MODIFY BELOW THIS LINE!
|
||||||
|
// --------------------------------------------
|
||||||
|
|
||||||
|
#ifndef FIRMWARE_LOAD_COMPILE
|
||||||
|
#define RADIO_CONFIGURATION_DATA_ARRAY { \
|
||||||
|
0x07, RF_POWER_UP, \
|
||||||
|
0x08, RF_GPIO_PIN_CFG, \
|
||||||
|
0x05, RF_GLOBAL_XO_TUNE_1, \
|
||||||
|
0x05, RF_GLOBAL_CONFIG_1, \
|
||||||
|
0x05, RF_PREAMBLE_CONFIG_1, \
|
||||||
|
0x10, RF_MODEM_MOD_TYPE_12, \
|
||||||
|
0x05, RF_MODEM_FREQ_DEV_0_1, \
|
||||||
|
0x10, RF_MODEM_TX_RAMP_DELAY_12, \
|
||||||
|
0x10, RF_MODEM_BCR_NCO_OFFSET_2_12, \
|
||||||
|
0x07, RF_MODEM_AFC_LIMITER_1_3, \
|
||||||
|
0x05, RF_MODEM_AGC_CONTROL_1, \
|
||||||
|
0x10, RF_MODEM_AGC_WINDOW_SIZE_12, \
|
||||||
|
0x09, RF_MODEM_RAW_CONTROL_5, \
|
||||||
|
0x08, RF_MODEM_RSSI_JUMP_THRESH_4, \
|
||||||
|
0x06, RF_MODEM_RAW_SEARCH2_2, \
|
||||||
|
0x06, RF_MODEM_SPIKE_DET_2, \
|
||||||
|
0x05, RF_MODEM_RSSI_MUTE_1, \
|
||||||
|
0x09, RF_MODEM_DSA_CTRL1_5, \
|
||||||
|
0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12, \
|
||||||
|
0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12, \
|
||||||
|
0x10, RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12, \
|
||||||
|
0x05, RF_PA_TC_1, \
|
||||||
|
0x0B, RF_SYNTH_PFDCP_CPFF_7, \
|
||||||
|
0x0C, RF_FREQ_CONTROL_INTE_8, \
|
||||||
|
0x08, RF_START_RX, \
|
||||||
|
0x05, RF_IRCAL, \
|
||||||
|
0x05, RF_IRCAL_1, \
|
||||||
|
0x05, RF_GLOBAL_CLK_CFG_1, \
|
||||||
|
0x05, RF_GLOBAL_CONFIG_1_1, \
|
||||||
|
0x05, RF_INT_CTL_ENABLE_1, \
|
||||||
|
0x08, RF_FRR_CTL_A_MODE_4, \
|
||||||
|
0x05, RF_PREAMBLE_CONFIG_STD_1_1, \
|
||||||
|
0x05, RF_PKT_CONFIG1_1, \
|
||||||
|
0x10, RF_MODEM_MOD_TYPE_12_1, \
|
||||||
|
0x05, RF_MODEM_FREQ_DEV_0_1_1, \
|
||||||
|
0x10, RF_MODEM_TX_RAMP_DELAY_12_1, \
|
||||||
|
0x10, RF_MODEM_BCR_NCO_OFFSET_2_12_1, \
|
||||||
|
0x07, RF_MODEM_AFC_LIMITER_1_3_1, \
|
||||||
|
0x05, RF_MODEM_AGC_CONTROL_1_1, \
|
||||||
|
0x10, RF_MODEM_AGC_WINDOW_SIZE_12_1, \
|
||||||
|
0x0E, RF_MODEM_RAW_CONTROL_10, \
|
||||||
|
0x06, RF_MODEM_RAW_SEARCH2_2_1, \
|
||||||
|
0x06, RF_MODEM_SPIKE_DET_2_1, \
|
||||||
|
0x05, RF_MODEM_RSSI_MUTE_1_1, \
|
||||||
|
0x09, RF_MODEM_DSA_CTRL1_5_1, \
|
||||||
|
0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12_1, \
|
||||||
|
0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12_1, \
|
||||||
|
0x10, RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12_1, \
|
||||||
|
0x05, RF_PA_TC_1_1, \
|
||||||
|
0x0B, RF_SYNTH_PFDCP_CPFF_7_1, \
|
||||||
|
0x0C, RF_FREQ_CONTROL_INTE_8_1, \
|
||||||
|
0x00 \
|
||||||
|
}
|
||||||
|
#else
|
||||||
|
#define RADIO_CONFIGURATION_DATA_ARRAY { 0 }
|
||||||
|
#endif
|
||||||
|
|
||||||
|
// DEFAULT VALUES FOR CONFIGURATION PARAMETERS
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ_DEFAULT 30000000L
|
||||||
|
#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER_DEFAULT 0x00
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH_DEFAULT 0x10
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP_DEFAULT 0x01
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET_DEFAULT 0x1000
|
||||||
|
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_PATCH_INCLUDED 0x00
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_PATCH_SIZE 0x00
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_PATCH { }
|
||||||
|
|
||||||
|
#ifndef RADIO_CONFIGURATION_DATA_ARRAY
|
||||||
|
#error "This property must be defined!"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ_DEFAULT
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER
|
||||||
|
#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER_DEFAULT
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH_DEFAULT
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP_DEFAULT
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET
|
||||||
|
#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET_DEFAULT
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define RADIO_CONFIGURATION_DATA { \
|
||||||
|
Radio_Configuration_Data_Array, \
|
||||||
|
RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER, \
|
||||||
|
RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH, \
|
||||||
|
RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP, \
|
||||||
|
RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET \
|
||||||
|
}
|
||||||
|
|
||||||
|
#endif /* RADIO_CONFIG_H_ */
|
||||||
Loading…
Reference in new issue