ac2ie
12 years ago
parent
7125791721
commit
ee0a0e0429
@ -0,0 +1,106 @@
|
|||||||
|
|
||||||
|
# This is the repeater callsign
|
||||||
|
# This must be equal to the OWNER value in the gateway software(g2_ircddb.cfg)
|
||||||
|
DVCALL=
|
||||||
|
|
||||||
|
# If you operate in "restriction mode", set RPTR equal to your personal callsign
|
||||||
|
# otherwise set RPTR equal to the value of DVCALL
|
||||||
|
RPTR=
|
||||||
|
|
||||||
|
# If you want to enable/disable the repeater, set these options.
|
||||||
|
# Each of these options can NOT be more than 8 characters.
|
||||||
|
# Each of these options can NOT be another user's callsign.
|
||||||
|
# Each of these options can NOT be another repeater or reflector.
|
||||||
|
# Each of these options can NOT be a YRCALL command.
|
||||||
|
# If these options are set, then they can NOT be equal to each other.
|
||||||
|
# Lets take an example:
|
||||||
|
# ENABLE_RF=RFISON
|
||||||
|
# DISABLE_RF=RFISOFF
|
||||||
|
# Using the above options, if you use YRCALL=RFISOFF in your radio
|
||||||
|
# then the repeater will be OFF
|
||||||
|
# and no audio will be copied over local RF
|
||||||
|
# and no audio will be accepted from any remote system.
|
||||||
|
ENABLE_RF=RFISON
|
||||||
|
DISABLE_RF=RFISOFF
|
||||||
|
|
||||||
|
# This must be equal to: FROM_REMOTE_G2_TIMEOUT + 1
|
||||||
|
# Note: FROM_REMOTE_G2_TIMEOUT is in the gateway configuration
|
||||||
|
REMOTE_TIMEOUT=3
|
||||||
|
|
||||||
|
# This is the module of the Dstar repeater
|
||||||
|
DVRPTR_MOD=B
|
||||||
|
|
||||||
|
# To protect the repeater owners from bad STN programs out there
|
||||||
|
# and to also protect the repeater owners from RF users that abuse the STN stuff
|
||||||
|
# Reject values in YRCALL that start with STN
|
||||||
|
# If you want to allow the local RF users to subscribe to remote STN groups,
|
||||||
|
# then set it to XXX or something that is invalid like 123
|
||||||
|
INVALID_YRCALL_KEY=XXX
|
||||||
|
|
||||||
|
# Your serial number
|
||||||
|
DVRPTR_SERIAL=12.19.D3.42
|
||||||
|
|
||||||
|
# For repeater module A: DVRPTR_INTERNAL_PORT=19998
|
||||||
|
# For repeater module B: DVRPTR_INTERNAL_PORT=19999
|
||||||
|
# For repeater module C: DVRPTR_INTERNAL_PORT=20000
|
||||||
|
# Repeater IP and port, the repeater runs here
|
||||||
|
DVRPTR_INTERNAL_IP=0.0.0.0
|
||||||
|
# for module B, port is 19999
|
||||||
|
DVRPTR_INTERNAL_PORT=19999
|
||||||
|
|
||||||
|
# The Internal G2 IP and port
|
||||||
|
GATEWAY_IP=127.0.0.1
|
||||||
|
GATEWAY_PORT=19000
|
||||||
|
|
||||||
|
# Some settings for your DV-RPTR modem
|
||||||
|
RF_AUDIO_Level=60
|
||||||
|
|
||||||
|
# Do you want an ACK back ?
|
||||||
|
RPTR_ACK=Y
|
||||||
|
|
||||||
|
# ACK delay in milliseconds(ms)
|
||||||
|
# Minimum is 1, maximum is 999
|
||||||
|
# If you do not get a repeater ACK, then make it a higher number
|
||||||
|
# Some radios get the ACK in 250ms, other radios require 750ms
|
||||||
|
ACK_DELAY=300
|
||||||
|
|
||||||
|
# For each packet inside the ACK, delay so many milliseconds,
|
||||||
|
# so the ICOM Dstar radio can process the ACK
|
||||||
|
DELAY_BETWEEN=19
|
||||||
|
|
||||||
|
# This is the TX-delay in milliseconds and it is used to delay the PTT.
|
||||||
|
# Seme radios have "SLOW" switching time,
|
||||||
|
# If your radio switches slow from RX to TX, then give your radio more time to switch, maybe 250 ms
|
||||||
|
# If your radio switches fast from RX to TX, then you could set it to 100 ms or maybe less
|
||||||
|
# But the best value should be the one to match your radio, so read the manual for your radio.
|
||||||
|
# In tests that were done for SLOW and FAST radios, we set it to 100 for FAST radios and 250 for SLOW radios.
|
||||||
|
TX_DELAY=250
|
||||||
|
|
||||||
|
# Dead firmware ?
|
||||||
|
# Lets say that you set RQST_COUNT=10
|
||||||
|
# When there is NO local RF activity, (we do NOT receive anything from the DV-RPTR modem),
|
||||||
|
# then every 2 seconds we request the status from the DV-RPTR modem.
|
||||||
|
# If the DV-RPTR modem does NOT reply to our command, then after sending the command 10 times(RQST_COUNT)
|
||||||
|
# we have to assume the firmware in the DV-RPTR modem is DEAD.
|
||||||
|
# So, we send the command every 2 sedonds, and after sending the command 10 times,
|
||||||
|
# that is about (2 * 10) = 20 seconds,
|
||||||
|
# the repeater software will stop if the DV-RPTR modem does not respond after 20 seconds( 2 seconds * 10 times )
|
||||||
|
# and then the service script will restart the repeater software.
|
||||||
|
# This is used to protect the repeater owner from BAD firmware.
|
||||||
|
# Minimum value is 6.
|
||||||
|
# If you see in the log this: "Modem is not responding... shuttting down"
|
||||||
|
# Then that means that the firmware died and the DV-RPTR modem stopped responding.
|
||||||
|
# You can increase the value of RQST_COUNT if you have a slow computer,
|
||||||
|
# (or maybe your computer is running too many programs and can not service the USB/serial fast enough)
|
||||||
|
# but we were informed that this is a bug in the firmware and they are trying to fix it.
|
||||||
|
# So, increasing the value for RQST_COUNT to higher than 10, does not make much sense.
|
||||||
|
RQST_COUNT=10
|
||||||
|
|
||||||
|
# If you want duplex, set it to Y
|
||||||
|
DUPLEX=N
|
||||||
|
|
||||||
|
# These values depend on what type of tranceiver is connected to your DV-RPTR modem
|
||||||
|
# Use either 0 or 1
|
||||||
|
RX_Inverse=1
|
||||||
|
TX_Inverse=0
|
||||||
|
|
||||||
File diff suppressed because it is too large
Load Diff
@ -0,0 +1,10 @@
|
|||||||
|
#!/bin/bash
|
||||||
|
|
||||||
|
while [ 1 ];
|
||||||
|
do
|
||||||
|
/usr/local/bin/dvrptr /usr/local/etc/dvrptr.cfg > /var/log/dvrptr.log 2>&1
|
||||||
|
sleep 3
|
||||||
|
done
|
||||||
|
|
||||||
|
exit 0
|
||||||
|
|
||||||
@ -0,0 +1,66 @@
|
|||||||
|
#!/bin/sh
|
||||||
|
# Start/stop the dstar dvrptr
|
||||||
|
#
|
||||||
|
### BEGIN INIT INFO
|
||||||
|
# Provides: dvrptr
|
||||||
|
# Required-Start:
|
||||||
|
# Required-Stop:
|
||||||
|
# Default-Start: 2 3 4 5
|
||||||
|
# Default-Stop: 0 1 6
|
||||||
|
# Short-Description: dvrptr
|
||||||
|
# Description: dvrptr
|
||||||
|
### END INIT INFO
|
||||||
|
|
||||||
|
. /lib/lsb/init-functions
|
||||||
|
|
||||||
|
DVRPTR_SH=/usr/local/bin/dvrptr.sh
|
||||||
|
DVRPTR_BIN=/usr/local/bin/dvrptr
|
||||||
|
DVRPTR_PIDFILE=/usr/local/dvrptr.sh_pidfile
|
||||||
|
|
||||||
|
start()
|
||||||
|
{
|
||||||
|
status_of_proc $DVRPTR_SH >/dev/null
|
||||||
|
RETVAL=$?
|
||||||
|
if [ "$RETVAL" = "0" ] ; then
|
||||||
|
echo "$DVRPTR_SH already running"
|
||||||
|
else
|
||||||
|
/bin/rm -rf $DVRPTR_PIDFILE
|
||||||
|
echo -n "Starting $DVRPTR_SH:"
|
||||||
|
start-stop-daemon --make-pidfile --pidfile $DVRPTR_PIDFILE --exec $DVRPTR_SH -S &
|
||||||
|
log_end_msg $?
|
||||||
|
fi
|
||||||
|
|
||||||
|
}
|
||||||
|
|
||||||
|
stop() {
|
||||||
|
start-stop-daemon --pidfile $DVRPTR_PIDFILE --retry 5 -K
|
||||||
|
start-stop-daemon --exec $DVRPTR_BIN --retry 5 -K
|
||||||
|
/bin/rm -rf $DVRPTR_PIDFILE
|
||||||
|
}
|
||||||
|
|
||||||
|
case "$1" in
|
||||||
|
start)
|
||||||
|
start
|
||||||
|
;;
|
||||||
|
stop)
|
||||||
|
stop
|
||||||
|
;;
|
||||||
|
restart)
|
||||||
|
stop
|
||||||
|
start
|
||||||
|
;;
|
||||||
|
status)
|
||||||
|
echo -n "$DVRPTR_SH "
|
||||||
|
status_of_proc $DVRPTR_SH
|
||||||
|
|
||||||
|
echo -n "$DVRPTR_BIN "
|
||||||
|
status_of_proc $DVRPTR_BIN
|
||||||
|
;;
|
||||||
|
|
||||||
|
*) log_action_msg "Usage: /etc/init.d/dvrptr {start|stop|restart|status}"
|
||||||
|
exit 2
|
||||||
|
;;
|
||||||
|
|
||||||
|
esac
|
||||||
|
exit 0
|
||||||
|
|
||||||
Loading…
Reference in new issue