KB8PMY
/
DStarRepeater
mirror of https://github.com/g4klx/DStarRepeater.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
Branches Tags
${ item.name }
Create tag ${ searchTerm }
Create branch ${ searchTerm }
from 'c2406d9f11'
${ noResults }
DStarRepeater/CONFIGURATION.md

368 lines
12 KiB
Raw Blame History Escape

This file contains ambiguous Unicode characters!

This file contains ambiguous Unicode characters that may be confused with others in your current locale. If your use case is intentional and legitimate, you can safely ignore this warning. Use the Escape button to highlight these characters.

# DStarRepeater Configuration Reference
The configuration file uses INI format with `[Section]` headers, `Key=Value` pairs, and `#` comments. The format is compatible with MMDVMHost.
To get started, copy the example config and edit for your installation:
```bash
sudo cp /etc/dstarrepeater/dstarrepeater.ini.example /etc/dstarrepeater/dstarrepeater.ini
sudo nano /etc/dstarrepeater/dstarrepeater.ini
```
Then start the daemon:
```bash
dstarrepeaterd /etc/dstarrepeater/dstarrepeater.ini
```
---
## [General]
| Key | Default | Description |
|-----|---------|-------------|
| `Callsign` | `GB3IN C` | Repeater callsign, padded to 8 characters. 7-character base + 1-character module suffix (A–E). |
| `Gateway` | *(empty)* | Gateway callsign, padded to 8 characters (e.g. `GB3IN G`). Leave empty if not linked. |
| `Mode` | `0` | Operating mode — see [Mode Values](#mode-values) below. |
| `Ack` | `1` | Acknowledgement type — see [Ack Values](#ack-values). Forced to `0` in Gateway, TX Only, RX Only, and TX+RX modes. |
| `Restriction` | `0` | `1` = only whitelisted callsigns accepted. |
| `RPT1Validation` | `1` | `1` = only accept headers addressed to this repeater. |
| `DTMFBlanking` | `1` | `1` = mute DTMF tones from the audio stream. |
| `ErrorReply` | `1` | `1` = reply with error message for invalid commands. |
### Mode Values
| Value | Mode | Description |
|:-----:|------|-------------|
| `0` | Duplex | Full duplex repeater (simultaneous TX and RX) |
| `1` | Simplex | Simplex repeater |
| `2` | Gateway | Gateway mode (ack forced off, RPT1 validation forced on) |
| `3` | TX Only | Transmit only |
| `4` | RX Only | Receive only |
| `5` | TX and RX | Sequential transmit then receive (split-site) |
### Ack Values
| Value | Type | Description |
|:-----:|------|-------------|
| `0` | Off | No acknowledgement |
| `1` | BER | Respond with Bit Error Rate |
| `2` | Status | Respond with status message |
---
## [Log]
Logging levels match MMDVMHost: `0`=None, `1`=Debug, `2`=Message, `3`=Info, `4`=Warning, `5`=Error, `6`=Fatal. Higher values are more selective (fewer messages).
| Key | Default | Description |
|-----|---------|-------------|
| `FilePath` | `/var/log` | Directory for daily log files (`dstarrepeaterd-YYYY-MM-DD.log`). |
| `FileLevel` | `2` | Minimum level to write to log file. `0` = no file logging. |
| `DisplayLevel` | `2` | Minimum level to write to stdout. `0` = no stdout output. |
| `MQTTLevel` | `2` | Minimum level to forward to MQTT. `0` = no MQTT logging. |
---
## [Paths]
| Key | Default | Description |
|-----|---------|-------------|
| `Data` | `/usr/share/dstarrepeater` | Directory containing AMBE voice beacon files (`.ambe` and `.indx`). |
| `Audio` | `/var/log` | Directory for DVTool audio recordings and announcements. |
---
## [Network]
| Key | Default | Description |
|-----|---------|-------------|
| `GatewayAddress` | `127.0.0.1` | IP address of the gateway (ircDDBGateway or DStarGateway). |
| `GatewayPort` | `20010` | UDP port the gateway is listening on. |
| `LocalAddress` | `127.0.0.1` | Local IP address to bind. |
| `LocalPort` | `20011` | Local UDP port. |
| `Name` | *(empty)* | Network name for multi-repeater setups. |
---
## [Modem]
| Key | Default | Description |
|-----|---------|-------------|
| `Type` | `DVAP` | Hardware modem type (case-sensitive). |
Valid modem types:
| Value | Hardware |
|-------|----------|
| `DVAP` | DVAP USB Dongle |
| `DVMEGA` | DV-Mega board |
| `DV-RPTR V1` | DV-RPTR Version 1 |
| `DV-RPTR V2` | DV-RPTR Version 2 |
| `DV-RPTR V3` | DV-RPTR Version 3 |
| `GMSK Modem` | GMSK modem (Dutch*STAR) |
| `MMDVM` | Multi-Mode Digital Voice Modem |
| `Sound Card` | Sound card modem (ALSA/PortAudio) |
| `Split` | Multi-receiver split-site |
| `Icom Access Point/Terminal Mode` | Icom radio in AP/terminal mode |
Only configure the section matching your modem type.
---
## [Times]
| Key | Default | Description |
|-----|---------|-------------|
| `Timeout` | `180` | Transmission timeout in seconds. `0` to disable. |
| `AckTime` | `500` | Acknowledgement delay in milliseconds. |
---
## [Beacon]
| Key | Default | Description |
|-----|---------|-------------|
| `Time` | `600` | Beacon interval in seconds. `0` to disable. |
| `Text` | `D-Star Repeater` | Text transmitted in the beacon slow data field. |
| `Voice` | `0` | `1` = transmit a voice beacon in addition to data. |
| `Language` | `0` | Language for voice beacon — see [Language Values](#language-values). |
### Language Values
| Value | Language |
|:-----:|----------|
| `0` | English (UK) |
| `1` | Deutsch |
| `2` | Dansk |
| `3` | Francais |
| `4` | Italiano |
| `5` | Polski |
| `6` | Espanol |
| `7` | Svenska |
| `8` | Nederlands |
| `9` | English (US) |
| `10` | Norsk |
---
## [Announcement]
| Key | Default | Description |
|-----|---------|-------------|
| `Enabled` | `0` | `1` = enable announcement recording and playback. |
| `Time` | `500` | Announcement playback interval in seconds. |
| `RecordRPT1` | *(empty)* | RPT1 callsign that triggers recording. |
| `RecordRPT2` | *(empty)* | RPT2 callsign that triggers recording. |
| `DeleteRPT1` | *(empty)* | RPT1 callsign that triggers deletion. |
| `DeleteRPT2` | *(empty)* | RPT2 callsign that triggers deletion. |
---
## [Control]
DTMF remote control via D-Star headers. When enabled, specific YOURCALL values trigger actions.
| Key | Default | Description |
|-----|---------|-------------|
| `Enabled` | `0` | `1` = enable DTMF remote control. |
| `RPT1` | *(empty)* | RPT1 callsign required for control commands. |
| `RPT2` | *(empty)* | RPT2 callsign required for control commands. |
| `Shutdown` | *(empty)* | YOURCALL value to shut down the repeater. |
| `Startup` | *(empty)* | YOURCALL value to start up the repeater. |
| `Status1`–`Status5` | *(empty)* | YOURCALL values to trigger status messages 1–5. |
| `Command1`–`Command6` | *(empty)* | YOURCALL values for custom commands 1–6. |
| `Command1Line`–`Command6Line` | *(empty)* | Shell command executed when the corresponding command is triggered. |
| `Output1`–`Output4` | *(empty)* | YOURCALL values to toggle output relays 1–4. |
---
## [Controller]
External hardware controller for PTT, LEDs, and relay outputs.
| Key | Default | Description |
|-----|---------|-------------|
| `Type` | *(empty)* | Controller type — see [Controller Types](#controller-types). |
| `SerialConfig` | `1` | Pin/output configuration preset (1–5). |
| `PTTInvert` | `0` | `1` = invert PTT output (active low). |
| `ActiveHangTime` | `0` | Seconds to hold active state after last transmission. `0` to disable. |
### Controller Types
| Value | Description |
|-------|-------------|
| *(empty)* | No controller (dummy) |
| `GPIO` | Raspberry Pi GPIO pins |
| `UDRC` | UDRC board (Raspberry Pi) |
| `Velleman K8055 - 0` | Velleman K8055 USB board (address 0–3) |
| `URI USB - 1` | URI USB relay card (address 1–6) |
| `Serial - /dev/ttyUSB0` | Serial port controller |
| `Arduino - /dev/ttyUSB0` | Arduino controller via serial |
---
## [Outputs]
Default state of output relays at startup.
| Key | Default | Description |
|-----|---------|-------------|
| `Output1` | `0` | Output relay 1. `1` = on at startup. |
| `Output2` | `0` | Output relay 2. |
| `Output3` | `0` | Output relay 3. |
| `Output4` | `0` | Output relay 4. |
---
## [Frame Logging]
| Key | Default | Description |
|-----|---------|-------------|
| `Enabled` | `0` | `1` = record all D-Star frames to `.dvtool` files in the audio directory. |
---
## [Whitelist] / [Blacklist] / [Greylist]
Callsign access control lists. Each takes a single `File` key pointing to a text file with one callsign per line.
| Key | Default | Description |
|-----|---------|-------------|
| `File` | *(not set)* | Full path to the list file. Leave commented out to disable. |
Example:
```ini
[Whitelist]
File=/etc/dstarrepeater/rptr_whitelist.dat
```
---
## Modem-Specific Settings
Only configure the section matching your `[Modem] Type`.
### [DVAP]
| Key | Default | Description |
|-----|---------|-------------|
| `Port` | *(empty)* | Serial port (e.g. `/dev/ttyUSB0`). |
| `Frequency` | `145500000` | Operating frequency in Hz. |
| `Power` | `10` | Transmit power in dBm. |
| `Squelch` | `-100` | Squelch threshold in dBm. |
### [GMSK]
| Key | Default | Description |
|-----|---------|-------------|
| `InterfaceType` | `0` | `0` = libUSB, `1` = direct/serial. |
| `Address` | `768` | USB address in decimal (768 = 0x0300). |
### [DV-RPTR V1]
| Key | Default | Description |
|-----|---------|-------------|
| `Port` | *(empty)* | Serial port (e.g. `/dev/ttyUSB0`). |
| `RXInvert` | `0` | `1` = invert received signal polarity. |
| `TXInvert` | `0` | `1` = invert transmitted signal polarity. |
| `Channel` | `0` | `0` = Channel A, `1` = Channel B. |
| `ModLevel` | `20` | Modulation level (0–100%). |
| `TXDelay` | `150` | Transmit delay in milliseconds. |
### [DV-RPTR V2]
| Key | Default | Description |
|-----|---------|-------------|
| `Connection` | `0` | `0` = USB, `1` = Network. |
| `USBPort` | *(empty)* | USB serial port. |
| `Address` | `127.0.0.1` | Network address (when Connection=1). |
| `Port` | `0` | Network port (when Connection=1). |
| `TXInvert` | `0` | `1` = invert transmitted signal polarity. |
| `ModLevel` | `20` | Modulation level (0–100%). |
| `TXDelay` | `150` | Transmit delay in milliseconds. |
### [DV-RPTR V3]
Same keys as [DV-RPTR V2].
### [DVMEGA]
| Key | Default | Description |
|-----|---------|-------------|
| `Port` | *(empty)* | Serial port (e.g. `/dev/ttyAMA0`). |
| `Variant` | `0` | `0` = Modem, `1` = Radio 2m, `2` = Radio 70cm, `3` = Radio 2m/70cm. |
| `RXInvert` | `0` | `1` = invert received signal. |
| `TXInvert` | `0` | `1` = invert transmitted signal. |
| `TXDelay` | `150` | Transmit delay in milliseconds. |
| `RXFrequency` | `145500000` | Receive frequency in Hz (radio variants only). |
| `TXFrequency` | `145500000` | Transmit frequency in Hz (radio variants only). |
| `Power` | `100` | Transmit power 0–100% (radio variants only). |
### [MMDVM]
| Key | Default | Description |
|-----|---------|-------------|
| `Port` | *(empty)* | Serial port (e.g. `/dev/ttyACM0`). |
| `RXInvert` | `0` | `1` = invert received signal. |
| `TXInvert` | `0` | `1` = invert transmitted signal. |
| `PTTInvert` | `0` | `1` = invert PTT signal. |
| `TXDelay` | `50` | Transmit delay in milliseconds. |
| `RXLevel` | `100` | Receive level (0–100%). |
| `TXLevel` | `100` | Transmit level (0–100%). |
### [Sound Card]
| Key | Default | Description |
|-----|---------|-------------|
| `RXDevice` | *(empty)* | Sound card device name for receiving. |
| `TXDevice` | *(empty)* | Sound card device name for transmitting. |
| `RXInvert` | `0` | `1` = invert received signal. |
| `TXInvert` | `0` | `1` = invert transmitted signal. |
| `RXLevel` | `1.0` | Receive level multiplier (1.0 = unity gain). |
| `TXLevel` | `1.0` | Transmit level multiplier (1.0 = unity gain). |
| `TXDelay` | `150` | Transmit delay in milliseconds. |
| `TXTail` | `50` | Transmit tail in milliseconds (extra carrier after last frame). |
### [Split]
Multi-receiver split-site configuration using UDP.
| Key | Default | Description |
|-----|---------|-------------|
| `LocalAddress` | *(empty)* | Local IP address for split communication. |
| `LocalPort` | `0` | Local UDP port. |
| `Timeout` | `0` | Timeout in milliseconds. `0` to disable. |
TX/RX names are configured as indexed keys: `TXName0`–`TXName4` and `RXName0`–`RXName24`.
### [Icom]
| Key | Default | Description |
|-----|---------|-------------|
| `Port` | *(empty)* | Serial port (e.g. `/dev/ttyUSB0`). |
---
## [MQTT]
*Only used when built with `make MQTT=1`. See [MQTT.md](MQTT.md) for full details.*
| Key | Default | Description |
|-----|---------|-------------|
| `Host` | `127.0.0.1` | MQTT broker hostname or IP. Empty to disable MQTT at runtime. |
| `Port` | `1883` | Broker port. |
| `Auth` | `0` | `1` = authenticate with username/password. |
| `Username` | *(empty)* | Broker username (when Auth=1). |
| `Password` | *(empty)* | Broker password (when Auth=1). |
| `Keepalive` | `60` | Keepalive interval in seconds. |
| `Name` | `dstar-repeater` | Client name and topic prefix. |
### MQTT Topics
With `Name=dstar-repeater`:
| Topic | Content |
|-------|---------|
| `dstar-repeater/log` | Timestamped log messages (filtered by MQTTLevel). |
| `dstar-repeater/status` | JSON repeater status (1/sec). |
| `dstar-repeater/json` | Display-Driver-compatible D-Star events. |
Reference in new issue View Git Blame Copy Permalink

Powered by TurnKey Linux.