CubeSatSim

The CubeSat Simulator https://github.com/alanbjohnston/CubeSatSim/wiki is a low cost satellite emulator that runs on solar panels and batteries, transmits UHF radio telemetry, has a 3D printed frame, and can be extended by additional sensors and modules. This project is sponsored by the not-for-profit Radio Amateur Satellite Corporation, AMSAT® https://CubeSatSim.org

The three custom PCBs are the Main, Battery and Solar boards. Information including schematics and gerbers is in https://CubeSatSim.org/hardware

For information about the AMSAT STEM education program based on the CubeSatSim, see https://CubeSatSim.org/EducatorsGuide

For STEM activities to do with the CubeSatSim, see the https://CubeSatSim.org/ActivityGuides

There are several hardware versions and software branches to go with them - see below for information.

See the Wiki Software Install page for more details: https://github.com/alanbjohnston/CubeSatSim/wiki/2.-Software-Install. The software runs the Raspberry Pi Zero 2W and the Raspberry Pi 4B. Some of the software runs on a Raspberry Pi 3B, 3B+, Pi Zero, and Pi Zero W.

There are two ways to get the CubeSatSim(TM) software for your Pi.

One option is to download the disk image file and write it to a 16GB micro SD card or larger. The image is based on Raspberry Pi OS (Bookworm) Legacy. All software is installed, you just need to login to change your password and set your amateur radio callsign if you have one. You can run the ./update.sh script to update all packages and update and compile the latest CubeSatSim software.

The other option is to start with a Raspberry Pi OS (Rasbian) image (Bookworm Legacy - Trixie is not yet compatible) and run the installation script ./install.sh which will install and compile all the related software. This includes the following packages:

• wiringpi
• git
• libasound2-dev
• pi-power-button
• Direwolf
• rpitx
• python3-pip
• python3-smbus

Disk Image Option Steps

See the Wiki Software Install page for details: https://github.com/alanbjohnston/CubeSatSim/wiki/2.-Software-Install.

Installation Script Option Steps

Use the Raspberry Pi Imager https://www.raspberrypi.com/software/ and select the Bookworm Legacy option. Make sure you set your username as pi. You can also preset your password, localization, and WiFi settings.

   cd
   git clone http://github.com/alanbjohnston/CubeSatSim.git
   cd CubeSatSim
   git checkout master
   ./install

The installation script will run for quite a while. You will get prompted for your amateur radio callsign in all capitals, if you have one. If you don't you can put some other word which will be transmitted as a CW ID. You will also be prompted for your latitude and longitude for APRS packets. You will need to reboot after the script completes.

Here are some Quick Start Guides for operating the CubeSatSim: https://CubeSatSim.org/qsg

If you want to run the software on a Raspberry Pi Zero or Pi Zero W, you can install it on Bullseye. Here is a Bullseye Pi OS image that works: https://downloads.raspberrypi.org/raspios_full_armhf/images/raspios_full_armhf-2023-05-03/ Here is the file download link: https://downloads.raspberrypi.org/raspios_full_armhf/images/raspios_full_armhf-2023-05-03/2023-05-03-raspios-bullseye-armhf-full.img.xz

You can use this with the Raspberry Pi Imager, but under OS you need to choose the Use Custom option at the very bottom of the list, then select the downloaded image 2023-05-03-raspios-bullseye-armhf-full.img.xz

Unfortunately, Customization is not supported with a Custom image, so you can't preset your username, password, localization, and WiFi settings.

So after you write this image to your microSD card, you will need to connect a monitor and keyboard to your Pi Zero 2 to set these things (make sure you set pi as the username). After that, you can connect it to your WiFi and turn on ssh and vnc for remote access.

You can then follow the software installation steps and it work work. The only hiccup is that if you run the installer script while running the Desktop, the Direwolf installation will freeze. But you can just cycle the power to the Pi Zero 2, then run the installer script again and it will complete successfully. Alternatively, if you use sudo raspi-config to change to Boot to Console (System/ Boot Auto Login/ Console or Console Auto Login) then the installer script will complete without any issues.

Note: CubeSatSim expects to be installed as the pi user and references many paths in /home/pi/*. Installing as a different user will result in configuration files not saving along with many other issues.

To install the software follow the steps above.

Older Versions

There are several versions of the hardware and software to go with them:

• The original design used a Digital Transceiver Board for the Raspberry Pi (DigitalTxRxRPi) and APRS AFSK 1200 bps telemetry only. Use the aprs-digitaltxrx branch https://github.com/alanbjohnston/CubeSatSim/tree/aprs-digitaltxrx for this and the vB2 wiki page https://github.com/alanbjohnston/CubeSatSim/wiki/vB2-Home (e.g. run git checkout aprs-digitaltxrx before running the ./install.sh script)
• An updated design that used the Transmitter/Filter Board (TFB) instead of the the Transceiver Board. For the same APRS AFSK telemetry, use the aprs-rpitx branch https://github.com/alanbjohnston/CubeSatSim/tree/aprs-rpitx and the vB3 wiki page https://github.com/alanbjohnston/CubeSatSim/wiki/vB3-Home. (e.g. run git checkout aprs-rpitx before running the ./install.sh script) Note that this hardware can still use the master code branch.