Select CH0 reflect channel before set freq (in some rare cases dsp started but CH not ready)

Little code optimization
Add commented 600kHz I2C bus timings (work, give x1.5 speed, but need change DSP ready timings not by wait_count, need use chVTGetSystemTimeX() its better)

main.c

@@ -787,8 +787,8 @@ bool sweep(bool break_on_operation)
   // Also touch made some
   DSP_START(1); DSP_WAIT_READY;
   for (i = 0; i < sweep_points; i++) {         // 5300
-    delay = set_frequency(frequencies[i]);     // 700
     tlv320aic3204_select(0);                   // 60 CH0:REFLECT
+    delay = set_frequency(frequencies[i]);     // 700
     DSP_START(delay);                          // 1900
     //================================================
     // Place some code thats need execute while delay
@@ -1296,35 +1296,18 @@ void
 cal_collect(int type)
 {
   ensure_edit_config();
-
+  int dst, src;
   switch (type) {
-  case CAL_LOAD:
-    cal_status |= CALSTAT_LOAD;
-    memcpy(cal_data[CAL_LOAD], measured[0], sizeof measured[0]);
-    break;
-
-  case CAL_OPEN:
-    cal_status |= CALSTAT_OPEN;
-    cal_status &= ~(CALSTAT_ES|CALSTAT_APPLY);
-    memcpy(cal_data[CAL_OPEN], measured[0], sizeof measured[0]);
-    break;
-
-  case CAL_SHORT:
-    cal_status |= CALSTAT_SHORT;
-    cal_status &= ~(CALSTAT_ER|CALSTAT_APPLY);
-    memcpy(cal_data[CAL_SHORT], measured[0], sizeof measured[0]);
-    break;
-
-  case CAL_THRU:
-    cal_status |= CALSTAT_THRU;
-    memcpy(cal_data[CAL_THRU], measured[1], sizeof measured[0]);
-    break;
-
-  case CAL_ISOLN:
-    cal_status |= CALSTAT_ISOLN;
-    memcpy(cal_data[CAL_ISOLN], measured[1], sizeof measured[0]);
-    break;
+    case CAL_LOAD:  cal_status|= CALSTAT_LOAD;  dst = CAL_LOAD;  src = 0; break;
+    case CAL_OPEN:  cal_status|= CALSTAT_OPEN;  dst = CAL_OPEN;  src = 0; cal_status&= ~(CALSTAT_ES|CALSTAT_APPLY); break;
+    case CAL_SHORT: cal_status|= CALSTAT_SHORT; dst = CAL_SHORT; src = 0; cal_status&= ~(CALSTAT_ER|CALSTAT_APPLY); break;
+    case CAL_THRU:  cal_status|= CALSTAT_THRU;  dst = CAL_THRU;  src = 1; break;
+    case CAL_ISOLN: cal_status|= CALSTAT_ISOLN; dst = CAL_ISOLN; src = 1; break;
+    default:
+      return;
   }
+  // Copy calibration data
+  memcpy(cal_data[dst], measured[src], sizeof measured[0]);
   redraw_request |= REDRAW_CAL_STATUS;
 }
 
@@ -2209,6 +2192,10 @@ static const I2CConfig i2ccfg = {
   STM32_TIMINGR_PRESC(5U)  |
   STM32_TIMINGR_SCLDEL(3U) | STM32_TIMINGR_SDADEL(3U) |
   STM32_TIMINGR_SCLH(3U)   | STM32_TIMINGR_SCLL(9U),
+  // 600kHz @ SYSCLK 48MHz, manually get values, x1.5 I2C speed, but need calc timings
+//  STM32_TIMINGR_PRESC(3U)  |
+//  STM32_TIMINGR_SCLDEL(2U) | STM32_TIMINGR_SDADEL(2U) |
+//  STM32_TIMINGR_SCLH(4U)   | STM32_TIMINGR_SCLL(4U),
 #else
 #error "Need Define STM32_I2C1SW and set correct TIMINGR settings"
 #endif

plot.c

@@ -1636,27 +1636,17 @@ draw_cal_status(void)
     ili9341_drawstring(c, x, y);
     y += YSTEP;
   }
-
-  if (cal_status & CALSTAT_ED) {
-    ili9341_drawstring("D", x, y);
-    y += YSTEP;
-  }
-  if (cal_status & CALSTAT_ER) {
-    ili9341_drawstring("R", x, y);
-    y += YSTEP;
-  }
-  if (cal_status & CALSTAT_ES) {
-    ili9341_drawstring("S", x, y);
-    y += YSTEP;
-  }
-  if (cal_status & CALSTAT_ET) {
-    ili9341_drawstring("T", x, y);
-    y += YSTEP;
-  }
-  if (cal_status & CALSTAT_EX) {
-    ili9341_drawstring("X", x, y);
-    y += YSTEP;
-  }
+  int i;
+  static const struct {char text, zero, mask;} calibration_text[]={
+    {'D', 0, CALSTAT_ED},
+    {'R', 0, CALSTAT_ER},
+    {'S', 0, CALSTAT_ES},
+    {'T', 0, CALSTAT_ET},
+    {'X', 0, CALSTAT_EX}
+  };
+  for (i = 0; i < 5; i++, y+= YSTEP)
+    if (cal_status & calibration_text[i].mask)
+      ili9341_drawstring(&calibration_text[i].text, x, y);
 }
 
 // Draw battery level

si5351.c

@@ -338,7 +338,7 @@ static inline uint8_t si5351_getBand(uint32_t freq){
 // Minimum value is 2, freq change apply at next dsp measure, and need skip it
 #define DELAY_NORMAL 2
 // Additional delay for band 1 (remove unstable generation at begin)
-#define DELAY_BAND_1	 1
+#define DELAY_BAND_1       1
 // Band changes need additional delay after reset PLL
 #define DELAY_BANDCHANGE_1 2
 #define DELAY_BANDCHANGE_2 2