Update switch detection

NANOVNA_STM32_F072/board.h

@@ -177,7 +177,7 @@
                                      PIN_PUPDR_PULLDOWN(2) | \
                                      PIN_PUPDR_PULLDOWN(3) | \
                                      PIN_PUPDR_FLOATING(4) |         \
-                                     PIN_PUPDR_PULLDOWN(5) |         \
+                                     PIN_PUPDR_PULLUP(5) |         \
                                      PIN_PUPDR_FLOATING(6) |         \
                                      PIN_PUPDR_FLOATING(7) |         \
                                      PIN_PUPDR_PULLUP(GPIOA_MCO) | \

main.c

@@ -2119,7 +2119,7 @@ int main(void)
 
 #ifdef TINYSA3
   has_esd = ((palReadPort(GPIOB) & (1<<12)) ? false : true );
-
+  bool has_new_switch = ((palReadPort(GPIOA) & (1<<5)) ? false : true ) || ((palReadPort(GPIOB) & (1<<12)) ? false : true );
 #endif
 
 
@@ -2184,7 +2184,7 @@ int main(void)
 
 /* restore config */
 #ifdef TINYSA3
-  if (has_esd)
+  if (has_new_switch)
     config.switch_offset = -5.0;
 #endif
   config_recall();

sa_core.c

@@ -5381,8 +5381,7 @@ quit:
 #endif
     reset_settings(M_LOW);
     set_refer_output(-1);
-#ifdef TINYSA4
-  } else if (test == 1) {
+  } else if (false && test == 1) {
     float p2, p1, p;
     in_selftest = true;               // Spur search
     reset_settings(M_LOW);
@@ -5430,7 +5429,7 @@ quit:
         shell_printf("%d, %d\n\r", ((int)temp_t[j])/1000, (int)stored_t[j]);
     }
     reset_settings(M_LOW);
-  } else if (test == 2) {                                   // Attenuator test
+  } else if (false && test == 2) {                                   // Attenuator test
     in_selftest = true;
     reset_settings(M_LOW);
 #if 1
@@ -5441,7 +5440,9 @@ quit:
       set_attenuation(((float)j)/2.0);
       if (setting.test_argument)
         set_sweep_frequency(ST_CENTER, ((freq_t)setting.test_argument));
+#ifdef TINYSA4
       ultra_threshold = config.ultra_threshold;
+#endif
       test_acquire(TEST_LEVEL);                        // Acquire test
 	  test_validate(TEST_LEVEL);                       // Validate test
       if (j == 0)
@@ -5463,8 +5464,7 @@ quit:
     test_validate(TEST_ATTEN);                       // Validate test
 #endif
     reset_settings(M_LOW);
-#endif
-  } else if (test == 3) {                       // RBW step time search
+  } else if (false && test == 3) {                       // RBW step time search
     in_selftest = true;
     ui_mode_normal();
     test_prepare(TEST_RBW);
@@ -5572,8 +5572,7 @@ quit:
     reset_settings(M_LOW);
     setting.step_delay_mode = SD_NORMAL;
     setting.step_delay = 0;
-#ifdef TINYSA4
-  } else if (test == 4) {           // Calibrate modulation frequencies
+  } else if (false && test == 4) {           // Calibrate modulation frequencies
     reset_settings(M_LOW);
     set_mode(M_GENLOW);
     set_sweep_frequency(ST_CENTER, (freq_t)30000000);
@@ -5604,7 +5603,7 @@ quit:
 
     //    shell_printf("\n\rCycle time = %d\n\r", start_of_sweep_timestamp);
     reset_settings(M_LOW);
-  } else if (test == 5) {
+  } else if (false && test == 5) {
 //    reset_settings(M_LOW);                      // Make sure we are in a defined state
     in_selftest = true;
     switch (setting.test_argument) {
@@ -5640,7 +5639,7 @@ quit:
       set_sweep_frequency(ST_SPAN, 0);
       break;
     }
-  } else if (test == 6) {
+  } else if (false && test == 6) {
     in_selftest = true;               // MCU Spur search
     reset_settings(M_LOW);
     test_prepare(TEST_SPUR);
@@ -5658,8 +5657,7 @@ quit:
       shell_printf("%d: %9.3q\n\r",i, peakFreq);
       test_validate(TEST_SPUR);                       // Validate test
     }
-#endif
-  } else if (test == 7) {                       // RBW level test
+  } else if (false && test == 7) {                       // RBW level test
     in_selftest = true;
     ui_mode_normal();
     shell_printf("\n\r");

ui_sa.c

@@ -491,7 +491,9 @@ static const struct {
 #endif
 [KM_MARKER_TIME]  = {keypads_time        , "MARKER\nTIME"}, // KM_MARKER_TIME
 [KM_VAR]          = {keypads_freq        , "JOG\nSTEP"}, // jog step
+#ifdef __NOISE_FIGURE__
 [KM_NF]           = {keypads_plusmin     , "NOISE\nFIGURE"}, // noise figure of tinySA
+#endif
 };
 
 #if 0 // Not used
@@ -1175,7 +1177,9 @@ static UI_FUNCTION_ADV_CALLBACK(menu_measure_acb)
     }
     set_average(AV_OFF);
     set_external_gain(0.0);
+#ifdef TINYSA4
     set_extra_lna(false);
+#endif
   }
   switch(data) {
     case M_OFF:                                     // Off