getBrokers logs request-sent, header count, and completed-with-N-brokers-in-Xms or failed-after-Xms (frames + expected count) via FileLogService. A tester Share-logs capture then shows in plain text whether the broker pool load succeeds, stalls, or times out - which the raw BLE frames cannot reveal. Behaviour unchanged (parse-once refactor; all 13 service tests green).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The broker-pool GET put a single fixed 6s deadline on the entire paginated dump. A large pool (6+ brokers) streams field-by-field over ~8s and blew the deadline, so the client falsely reported the pool as not finished even though the device sent it all (the END terminator arrives after the client gave up). Re-arm an inactivity Timer on each received frame: a steadily-streaming dump never times out; only a genuine stall (no frame for the timeout window) fails. Adds a TDD test - a slow-but-steady dump, frames under the timeout but total far over it, must complete.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
A firmware build can ACK a broker enable/disable as success without applying it
(HV4; meshcore-firmware#179). The quick toggle and the editor save previously
trusted the ACK and showed a success snackbar, so an ack-but-no-op looked like
it worked.
Both paths now SET, wait a short settle, re-read the slot, and report what the
device ACTUALLY did:
- applied -> confirm
- notApplied -> warn "possible firmware issue"; the editor stays and re-seeds to
the device's true state instead of popping a false success
- unverified -> re-read failed (e.g. an enable that rebooted the device)
Every device is treated identically: the UI reflects the re-read, never assuming
a change took that the device didn't confirm.
- BrokerConfig.classifyApply pure classifier + BrokerApplyOutcome (unit-tested)
- ObserverConfigService.applySettleDelay
- wired into mqtt_brokers_screen quick toggle + broker_editor_screen save
- widget test for the ACK-but-not-applied path
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The write half of the broker editor, against RedCreek's confirmed field-at-a-time
contract. The existing 0xC0 key/value command already carries the broker keys --
no new wire codes -- so the codec comment at observer_config_client.dart:166 is
stale, not a gap.
- saveBroker(): disable a live slot first, write each changed field, write
`enabled` LAST. Stops at the first ERR/timeout and reports the failed field --
a partial save leaves the slot disabled, never live-corrupt (activation guard).
TDD: ordering + partial-failure tests.
- clearBroker(): mqtt.broker.<slot>.clear.
- getBroker(): single-slot re-GET via 14 per-field GETs (recovery / post-save
read), not the 84-frame pool dump. Password is write-only -> best-effort.
Key spellings (mqtt.broker.N.enabled / .clear, scalar field GET) are inferred
from the existing scheme; they're the one thing the joint firmware test confirms.
12/12 service tests green. UI (brokers screen + editor) next.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Three observer-delta fixes (per the #80 sync diagnosis / G2):
- A: settings screen gates the Observer category via context.select on the
supported flag, not a connector-wide context.watch -- the watch rebuilt the
whole settings screen on every sync frame, thrashing the UI thread.
- B: a flat Save re-reads only the flat settings (refresh includeBrokers:false),
never the 84-frame broker pool -- no BLE re-flood for a display toggle.
- C: the initial observer read is deferred until the device's channel/contact
sync settles, so it never competes with that sync for BLE.
TDD: B (no OCFG_BROKERS on a flat refresh) + C (refresh deferred while syncing,
fires once idle). Full observer suite green.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The G2 BLE log showed the config protocol works (GETs return values; the broker
dump starts) but the firmware's broker dump stalls without BROKERS_END, so
getBrokers() times out. The client was treating that as a TOTAL failure --
discarding the 7 flat settings it read cleanly and blanking the pane.
Now the broker pool loads independently: refresh() builds + shows the flat
config even when getBrokers fails, flags brokersUnavailable, and the pane shows
the broker section as "unavailable" instead of going stale. Flat settings stay
usable. TDD red->green; full observer suite (39) green.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Closes the 2 MINOR findings from the G1 re-review (#76):
- MINOR-A: ObserverConfigService.refresh() no longer wipes lastError / clears
stale on a PARTIAL read. A null from any getFlat is a failed read; the
snapshot is marked stale and the error kept (error-visibility).
- MINOR-B: the settings pane validates status_interval against the firmware
range (10-3600) before sending; an out-of-range value is not put on the wire
and the user is told.
TDD: both tests RED first (current sent '5'; refresh wiped the error), GREEN
after. Full observer suite (37 tests) green.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Greens A2's adversarial tests, fixing the Gemini findings:
- BLOCKER #1 (race): a chain-lock (_serialized) serializes every transport
round-trip, so overlapping refresh()/setFlat() can no longer cross responses
(firmware has no request id; responses correlate by order).
- MINOR #6 (secret leak): error messages redact secret key names
(wifi.pwd / *.password / *.pwd -> "<secret>").
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- screens/settings/observer_settings_view.dart: staged-save pane for WiFi
(ssid/pwd/enabled), MQTT region (iata/status_interval), display
(always_on/rotation 0|180), with Save (changed keys only) + Refresh +
stale/error banners; the broker pool renders read-only (enable/clear await
the firmware F-task).
- settings_screen.dart: register the Observer category, gated on
ObserverConfigService.supported (re-evaluated as the connector's offband_caps
flips on connect/disconnect).
- connector/meshcore_connector.dart: parse the offband_caps byte (device-info
byte 82, after path_hash_mode) + expose offbandCaps.
- services/observer_config_service.dart: supported computed live from the
connector (version gate + cap bit).
- main.dart: provide ObserverConfigService.
Strings are English-only pending l10n ARB keys.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Strycher