You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
82 lines
2.9 KiB
82 lines
2.9 KiB
|
|
# This is the configuration file for the DVAP device(2m dongle with antenna)
|
|
|
|
# This is Dstar repeater callsign
|
|
# Use a correct repeater call.
|
|
# If you set RPTR different from the OWNER
|
|
# then only the RF user identified by RPTR callsign can talk on this repeater.
|
|
# This mode is called "restriction" mode and in some countries(UK,...)
|
|
# it is the only valid mode that you can use, while waiting for a repeater license.
|
|
# In a case like this, set RPTR to be your personal callsign
|
|
RPTR=AC2IE
|
|
|
|
# This is the Gateway callsign
|
|
# This must be equal to the OWNER value in the gateway software(g2_ircddb.cfg)
|
|
OWNER=AC2IE
|
|
|
|
# To protect the repeater owners from bad STN programs out there
|
|
# and to also protect the repeater owners from RF users that abuse the STN stuff
|
|
# Reject values in YRCALL that start with STN
|
|
# If you want to allow the local RF users to subscribe to remote STN groups,
|
|
# then set it to XXX or something that is invalid like 123
|
|
INVALID_YRCALL_KEY=STN
|
|
|
|
# This is the module of the Dstar repeater
|
|
# Please read the comments about RPTR_PORT below
|
|
RPTR_MOD=C
|
|
|
|
# This identifies the IP for the repeater(controler)
|
|
# The DVAP device will run here
|
|
# For repeater module A: RPTR_PORT=19998
|
|
# For repeater module B: RPTR_PORT=19999
|
|
# For repeater module C: RPTR_PORT=20000
|
|
RPTR_VIRTUAL_IP=0.0.0.0
|
|
RPTR_PORT=20000
|
|
|
|
# This is the INTERNAL IP and PORT of your local G2 gateway
|
|
G2_INTERNAL_IP=127.0.0.1
|
|
G2_PORT=19000
|
|
|
|
# This is the serial number of your DVAP device
|
|
DVP_SERIAL=AP052344
|
|
|
|
# This is your 2m frequency for the DVAP device, Between 144000000 and 148000000
|
|
DVP_FREQ=146550000;
|
|
|
|
# This is the power level for the DVAP device, Between -12 and 10
|
|
DVP_PWR=10;
|
|
|
|
# This is the squelch setting for the DVAP device, between -128 and -45
|
|
DVP_SQL=-80;
|
|
|
|
# This is the offset frequency for the DVAP device, between -2000 and 2000
|
|
DVP_OFF=0;
|
|
|
|
# How long before we say that the local gateway has stopped sending packets to our repeater.
|
|
# This value is in seconds.
|
|
# Lets say that you set REMOTE_TIMEOUT=2 seconds and WAIT_FOR_PACKETS=25 milliseconds
|
|
# The program does a small calculation: ( (REMOTE_TIMEOUT * 1000) / WAIT_FOR_PACKETS))
|
|
# So that is (2000 / 25) = 80 = number_of_times_to_loop
|
|
# This calculated value of 80 is the number of times we will loop waiting for
|
|
# packets from the remote system.
|
|
# A value of 2 is sufficient. Minimum is 1 seconds.
|
|
REMOTE_TIMEOUT=2
|
|
|
|
# This is used in a loop to wait for packets from your local gateway
|
|
# This is in milliseconds
|
|
WAIT_FOR_PACKETS=25
|
|
|
|
# This is in seconds,
|
|
# It allows the dvap to re-initialize before we send the repeater ack back to it
|
|
DELAY_BEFORE=2
|
|
|
|
# This is in milliseconds
|
|
# Dstar packets should reach the dvap at a rate of about 17-23 milliseconds
|
|
# We use that when we send a repeater ack back to the DVAP
|
|
DELAY_BETWEEN=19
|
|
|
|
# Do you want a repeater ack sent to dvap, after the local RF radio user releases PTT ?
|
|
# Valid values are Y or N
|
|
RPTR_ACK=Y
|
|
|