You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
139 lines
2.4 KiB
139 lines
2.4 KiB
# D-Star Repeater configuration for a Raspberry Pi Zero 2 W with an SX1255 HAT.
|
|
# Author: Karel Kadlec (OK1LBC) <xkk@post.cz>
|
|
#
|
|
# Install to: /etc/dstarrepeater/dstarrepeater.ini
|
|
|
|
[General]
|
|
# Your repeater callsign (8 characters + optional module letter).
|
|
Callsign=GB3IN C
|
|
Gateway=
|
|
# 0=Duplex, 1=Simplex, 2=Gateway, 3=TXOnly, 4=RXOnly, 5=TX+RX
|
|
Mode=0
|
|
# 0=None, 1=BER, 2=Status
|
|
Ack=1
|
|
Restriction=0
|
|
RPT1Validation=1
|
|
DTMFBlanking=1
|
|
ErrorReply=1
|
|
|
|
[Log]
|
|
FilePath=/var/log
|
|
FileLevel=2
|
|
DisplayLevel=2
|
|
MQTTLevel=2
|
|
|
|
[Paths]
|
|
Data=/usr/share/dstarrepeater
|
|
Audio=/var/log
|
|
|
|
[Network]
|
|
GatewayAddress=127.0.0.1
|
|
GatewayPort=20010
|
|
LocalAddress=127.0.0.1
|
|
LocalPort=20011
|
|
Name=
|
|
|
|
[Modem]
|
|
# SX1255 = direct I/Q D-STAR modem over I2S/SPI.
|
|
Type=SX1255
|
|
|
|
[SX1255]
|
|
# ALSA I/Q devices created by the genericstereoaudiocodec overlay.
|
|
RXDevice=hw:GenericStereoAu,1,0
|
|
TXDevice=hw:GenericStereoAu,0,0
|
|
SPIDevice=/dev/spidev0.0
|
|
SPISpeed=500000
|
|
|
|
# Reset pin on the Pi Zero 2 W:
|
|
# libgpiod: /dev/gpiochip0 line 25 (BCM GPIO_25)
|
|
# sysfs: global number 537 (base 512 + 25)
|
|
ResetChip=/dev/gpiochip0
|
|
ResetLine=25
|
|
ResetGPIO=537
|
|
|
|
# PA PTT output (BCM GPIO_17 = header pin 11). Driven high while transmitting
|
|
# and low while idle; set PTTInvert=1 for an active-low PA key line.
|
|
PTTChip=/dev/gpiochip0
|
|
PTTLine=17
|
|
PTTInvert=0
|
|
|
|
# Repeater frequencies in Hz (SX1255 range: 410-510 MHz).
|
|
RXFrequency=430975020
|
|
TXFrequency=438575000
|
|
|
|
# RX synthesiser is tuned RXFrequency+RXShift; the mixer brings the signal to
|
|
# DC and avoids the LO spike. Keep -25000 unless you know what you are doing.
|
|
RXShift=-25000
|
|
|
|
# Peak GMSK deviation. D-Star h=0.5 at 4800 baud => 1200 Hz.
|
|
TXDeviation=1200
|
|
RXInvert=0
|
|
TXInvert=0
|
|
RXLevel=1.0
|
|
TXLevel=1.0
|
|
TXDelay=150
|
|
TXTail=50
|
|
|
|
[Times]
|
|
Timeout=180
|
|
AckTime=500
|
|
|
|
[Beacon]
|
|
Time=600
|
|
Text=D-Star Repeater
|
|
Voice=0
|
|
Language=0
|
|
|
|
[Announcement]
|
|
Enabled=0
|
|
Time=500
|
|
RecordRPT1=
|
|
RecordRPT2=
|
|
DeleteRPT1=
|
|
DeleteRPT2=
|
|
|
|
[Control]
|
|
Enabled=0
|
|
RPT1=
|
|
RPT2=
|
|
Shutdown=
|
|
Startup=
|
|
Status1=
|
|
Status2=
|
|
Status3=
|
|
Status4=
|
|
Status5=
|
|
Command1=
|
|
Command1Line=
|
|
Command2=
|
|
Command2Line=
|
|
Command3=
|
|
Command3Line=
|
|
Command4=
|
|
Command4Line=
|
|
Command5=
|
|
Command5Line=
|
|
Command6=
|
|
Command6Line=
|
|
Output1=
|
|
Output2=
|
|
Output3=
|
|
Output4=
|
|
|
|
# The SX1255 modem handles RX/TX switching itself over SPI, so no external
|
|
# PTT controller is required.
|
|
[Controller]
|
|
Type=
|
|
SerialConfig=1
|
|
PTTInvert=0
|
|
ActiveHangTime=0
|
|
|
|
[Outputs]
|
|
Output1=0
|
|
Output2=0
|
|
Output3=0
|
|
Output4=0
|
|
|
|
[Frame Logging]
|
|
Enabled=0
|