Create Payload_BME280_Pro_Micro.ino

arduino/Payload_BME280_Pro_Micro.ino

@@ -0,0 +1,80 @@
+#include <Wire.h>
+#include <Adafruit_Sensor.h>
+#include <Adafruit_BME280.h>
+#define SEALEVELPRESSURE_HPA (1013.25)
+
+//#define TESTING  // Define to test on Serial Monitor
+
+Adafruit_BME280 bme;
+int counter = 0;
+int RXLED = 17;  // The RX LED has a defined Arduino pin
+
+void setup() {
+
+  Serial.begin(9600); // Serial Monitor for testing
+
+  Serial1.begin(9600);  // Pi UART
+
+  Serial.println("Starting!");
+
+
+  digitalWrite(RXLED, LOW);   // set the RX LED ON
+  TXLED0; //TX LED is not tied to a normally controlled pin so a macro is needed, turn LED OFF
+  delay(50);              // wait for a second
+  digitalWrite(RXLED, HIGH);   // set the RX LED ON
+  TXLED0; //TX LED is not tied to a normally controlled pin so a macro is needed, turn LED OFF
+
+  if (!bme.begin(0x76)) {
+    Serial.println("Could not find a valid BME280 sensor, check wiring!");
+    while (1);
+  }
+}
+
+void loop() {
+
+#ifdef TESTING
+  if (Serial.available() > 0) {
+    digitalWrite(RXLED, LOW);   // set the RX LED ON
+    TXLED0; //TX LED is not tied to a normally controlled pin so a macro is needed, turn LED OFF
+    delay(50);              // wait for a second
+    digitalWrite(RXLED, HIGH);   // set the RX LED ON
+    TXLED0; //TX LED is not tied to a normally controlled pin so a macro is needed, turn LED OFF
+    char result = Serial.read();
+    //    Serial1.println(result);
+    Serial.print("OK BME280 ");
+    Serial.print(bme.readTemperature());
+    Serial.print(" ");
+    Serial.print(bme.readPressure() / 100.0F);
+    Serial.print(" ");
+    Serial.print(bme.readAltitude(SEALEVELPRESSURE_HPA));
+    Serial.print(" ");
+    Serial.println(bme.readHumidity());
+
+    //  Serial1.println(counter++);
+  }
+#else
+  if (Serial1.available() > 0) {
+    digitalWrite(RXLED, LOW);   // set the RX LED ON
+    TXLED0; //TX LED is not tied to a normally controlled pin so a macro is needed, turn LED OFF
+    delay(50);              // wait for a second
+    digitalWrite(RXLED, HIGH);   // set the RX LED ON
+    TXLED0; //TX LED is not tied to a normally controlled pin so a macro is needed, turn LED OFF
+    char result = Serial1.read();
+    //    Serial1.println(result);
+//    Serial1.println("OK ");
+/**/    
+    Serial1.print("OK BME280 ");
+    Serial1.print(bme.readTemperature());
+    Serial1.print(" ");
+    Serial1.print(bme.readPressure() / 100.0F);
+    Serial1.print(" ");
+    Serial1.print(bme.readAltitude(SEALEVELPRESSURE_HPA));
+    Serial1.print(" ");
+    Serial1.println(bme.readHumidity());
+/**/
+    //  Serial1.println(counter++);
+  }
+#endif
+
+  delay(100);
+}