# # Digital Voice Modem - Host Software Configuration # # Flag indicating whether the host will run as a background or foreground task. daemon: true # # Logging Configuration # # Logging Levels: # 1 - Debug # 2 - Message # 3 - Informational # 4 - Warning # 5 - Error # 6 - Fatal # log: # Flag indicating whether or not the NON-AUTHORITATIVE errors should be logged. disableNonAuthoritiveLogging: false # Console display logging level (used when in foreground). displayLevel: 1 # File logging level. fileLevel: 1 # Flag indicating file logs should be sent to syslog instead of a file. useSyslog: false # Full path for the directory to store the log files. filePath: . # Full path for the directory to store the activity log files. activityFilePath: . # Log filename prefix. fileRoot: DVM # # Network Configuration # network: # Flag indicating whether or not host networking is enabled. enable: true # Network Peer ID id: 100000 # Hostname/IP address of the FNE to connect to. address: 127.0.0.1 # Port number of the FNE to connect to. port: 62031 # FNE access password. password: "PASSWORD" # Flag indicating whether or not host endpoint networking is encrypted. encrypted: false # AES-256 32-byte Preshared Key # (This field *must* be 32 hex bytes in length or 64 characters # 0 - 9, A - F.) presharedKey: "000102030405060708090A0B0C0D0E0F000102030405060708090A0B0C0D0E0F" # Maximum allowable DMR network jitter. jitter: 360 # Flag indicating whether DMR slot 1 traffic will be passed. slot1: true # Flag indicating whether DMR slot 2 traffic will be passed. slot2: true # Flag indicating whether the local host lookup tables (RID, TGID, etc) will be updated from the network. updateLookups: false # Flag indicating whether the local host lookup tables will be saved to local files when updated from the network # This is handy if your site occasionally operates in site trunking mode without a connection to the FNE saveLookups: false # Flag indicating whether or not the host activity log will be sent to the network. allowActivityTransfer: true # Flag indicating whether or not the host diagnostic log will be sent to the network. allowDiagnosticTransfer: true # Flag indicating whether or not the host status will be sent to the network. allowStatusTransfer: true # Flag indicating whether or not verbose debug logging is enabled. debug: false # Flag indicating whether or not REST API is enabled. restEnable: false # IP address of the network interface to listen for REST API on (or 0.0.0.0 for all). restAddress: 127.0.0.1 # Port number for REST API to listen on. restPort: 9990 # Flag indicating whether or not REST API is operating in SSL mode. restSsl: false # HTTPS/TLS certificate. restSslCertificate: web.crt # HTTPS/TLS key file. restSslKey: web.key # REST API authentication password. restPassword: "PASSWORD" # Flag indicating whether or not verbose REST API debug logging is enabled. restDebug: false # # Digital Protocol Configuration # protocols: # # Digital Mobile Radio # dmr: # Flag indicating whether or not the protocol is enabled. enable: true # # DMR Roaming Beacon (and TSCC) Timing Configuration # beacons: # Flag indicating whether or not DMR roaming beacons are enabled. enable: false # Time between roaming beacon bursts. (seconds) interval: 60 # Amount of time to transmit roaming beacon. (seconds) duration: 3 # # DMR Timeslot Control Channel (TSCC) Configuration # control: # Flag indicating whether or not this TSCC is a dedicated CC. dedicated: false # Flag indicating whether or not TSCC is enabled. enable: false # DMR slot number to transmit TSCC data on. slot: 1 # Flag indicating whether or not the source ID validation before granting disabled. disableGrantSourceIdCheck: false # Flag indicating whether or not a TGID will be tested for affiliations before being granted. ignoreAffiliationCheck: false # Flag indicating whether or not received RF embedded LC data only should be transmitted. embeddedLCOnly: false # Flag indicating whether talker alias data should be dumped to the log. dumpTAData: true # Flag indicating whether verbose dumping of DMR data packets is enabled. dumpDataPacket: false # Flag indicating whether or not this host will repeat DMR data traffic. repeatDataPacket: true # Flag indicating whether verbose dumping of DMR CSBK data is enabled. dumpCsbkData: false # Flag indicating unit registration will be verified after some operations. verifyReg: false # Flag indicating automated 12-hour idle unit registration timeout is disabled. disableUnitRegTimeout: false # Specifies the random wait delay for a subscriber. # (This should not be altered.) nRandWait: 8 # Specifies the random back-off count in DMR TDMA frames. # (This should not be altered.) backOff: 1 # Amount of time to hang after a voice call. callHang: 5 # Amount of time to continue transmitting after the end of traffic. txHang: 8 # BER/Error threshold for silencing voice packets. (0 or 141 disables) silenceThreshold: 21 # Maximum number of lost frames before terminating a call. frameLossThreshold: 2 # Internal data queue size (in DMR frames). This is the queue used internally to buffer frames before they # are sent to the air interface modem. queueSize: 31 # Flag indicating whether or not verbose logging is enabled. verbose: true # Flag indicating whether or not debug logging is enabled. debug: false # # Project 25 # p25: # Flag indicating whether or not the protocol is enabled. enable: true # Sets the number of TDU preambles to transmit at the start of a transmission. tduPreambleCount: 6 # # P25 Control Channel Configuration # control: # Flag indicating whether or not TSBK data support is enabled. enable: false # Flag indicating whether or not TSBK requets will optionally acknowledge incoming requests. ackRequests: true # Flag indicating whether or not this CC is a dedicated CC. dedicated: false # Flag indicating whether CC data will be broadcast. broadcast: true # Time between non-dedicated CC broadcasts. (seconds) interval: 300 # Amount of time to transmit non-dedicated CC broadcasts. (seconds) duration: 1 # Flag to disable TSDU triple-block transmissions and instead transmit single-block TSDUs. disableTSDUMBF: false # Flag to enable optional TIME_DATE_ANNC TSBK during a CC broadcast. enableTimeDateAnn: false # Flag indicating whether or not the source ID validation before granting disabled. disableGrantSourceIdCheck: false # Flag indicating immediate TSDUs will be sent twice. redundantImmediate: true # Flag indicating whether redundant grant responses should be transmitted. redundantGrantTransmit: false # Flag indicating whether or not to ignore voice frames on a control channel # This comes in handy if you're running non-dedicated with an FNE so the CC doesn't repeat voice traffic. controlOnly: false # Flag indicating whether or not a voice HDU will transmitted at the start of a call from the network. disableNetworkHDU: false # Flag indicating whether or not network calls will generate a channel grant. # (This applies only in conventional operations where channel granting is utilized and RF-only talkgroup # steering is required.) disableNetworkGrant: false # Flag indicating whether or not a TGID will be tested for affiliations before being granted. ignoreAffiliationCheck: false # Flag indicating that the host will attempt to automatically inhibit unauthorized RIDs (those not in the # RID ACL list). inhibitUnauthorized: false # Flag indicating the fallback legacy group grant for radios that do not support group affilition to # have group grants transmitted. (Useful for alerting the FNE to affiliations to TGIDs for radios that # do not properly support group affiliation.) legacyGroupGrnt: true # Flag indicating the fallback legacy group registration. (Same as above except for group affiliations.) legacyGroupReg: false # Flag indicating the host should send a network grant demand TDU for conventional traffic. convNetGrantDemand: false # Flag indicating the host should demand a full unit registration for a refused affiliation request. demandUnitRegForRefusedAff: true # Flag indicating the host should verify group affiliation. verifyAff: false # Flag indicating the host should verify unit registration. verifyReg: false # Flag indicating automated 12-hour idle unit registration timeout is disabled. disableUnitRegTimeout: false # Flag indicating the host requires LLA verification before allowing unit registration. requireLLAForReg: false # Flag indicating whether verbose dumping of P25 data packets is enabled. dumpDataPacket: false # Flag indicating whether or not this host will repeat P25 data traffic. repeatDataPacket: true # Flag indicating whether verbose dumping of P25 TSBK data is enabled. dumpTsbkData: false # Amount of time to hang after a voice call. callHang: 5 # Flag indicating whether or not the host will acknowledge status packets. noStatusAck: false # Flag indicating whether or not the host will acknowledge message packets. noMessageAck: true # Flag indicating that unit-to-unit availiability checks should be performed for a private call. unitToUnitAvailCheck: false # Flag indicating explicit source ID support is enabled. allowExplicitSourceId: true # Flag indicating whether or not the host will respond to SNDCP data requests. sndcpSupport: false # BER/Error threshold for silencing voice packets. (0 or 1233 disables) silenceThreshold: 124 # Maximum number of lost frames before terminating a call. frameLossThreshold: 6 # Internal data queue size (in P25 LDU frames). This is the queue used internally to buffer frames before they # are sent to the air interface modem. queueSize: 12 # Flag indicating whether or not verbose logging is enabled. verbose: true # Flag indicating whether or not debug logging is enabled. debug: false # # Next Generation Digital Narrowband # nxdn: # Flag indicating whether or not the protocol is enabled. enable: false # # NXDN Control Channel Configuration # control: # Flag indicating whether or not CC is enabled. enable: false # Flag indicating whether or not this CC is a dedicated CC. dedicated: false # Flag indicating whether CC data will be broadcast. broadcast: true # Time between non-dedicated CC broadcasts. (seconds) interval: 300 # Amount of time to transmit non-dedicated CC broadcasts. (seconds) duration: 1 # Flag indicating whether or not the source ID validation before granting disabled. disableGrantSourceIdCheck: false # Flag indicating whether or not a TGID will be tested for affiliations before being granted. ignoreAffiliationCheck: false # Flag indicating the host should verify group affiliation. verifyAff: false # Flag indicating the host should verify unit registration. verifyReg: false # Flag indicating automated 12-hour idle unit registration timeout is disabled. disableUnitRegTimeout: false # Flag indicating whether verbose dumping of NXDN RCCH data is enabled. dumpRcchData: false # Amount of time to hang after a voice call. callHang: 5 # BER/Error threshold for silencing voice packets. (0 or 144 disables) silenceThreshold: 14 # Maximum number of lost frames before terminating a call. frameLossThreshold: 4 # Internal data queue size (in NXDN frames). This is the queue used internally to buffer frames before they # are sent to the air interface modem. queueSize: 31 # Flag indicating whether or not verbose logging is enabled. verbose: true # Flag indicating whether or not debug logging is enabled. debug: false # # System Configuration # system: # Textual label of this host. identity: ABCD123 # Total call transmit time maximum. (seconds) timeout: 180 # Flag indicating whether or not the host is operating in duplex (simultaneous Rx/Tx) or simplex operation. duplex: true # Flag indicating whether or not the host should utilize the same frequency in simplex operation # (instead of split frequency). simplexSameFrequency: false # Amount of time the host will "hang" on a digital mode in multi-mode operation. (seconds) modeHang: 10 # Amount of time the host will "hang" on a RF received digital mode in multi-mode operation. (seconds) # rfModeHang: 10 # Amount of time the host will "hang" on a network received digital mode in multi-mode operation. (seconds) # netModeHang: 10 # Flag indicating the host is operating in a single digital mode. fixedMode: false # Amount of time the host will "hang" on the last TGID received via RF before returning to allowing all # TGID traffic. This applies only to network traffic, it essentially allows time-based filtering of network # traffic for the last TGID received. rfTalkgroupHang: 10 # Sets the amount of delay between "ticks" of the processing loop when the host is active (i.e. # processing traffic). (ms) [Note: Default value is recommend, normally this should not be changed.] activeTickDelay: 5 # Sets the amount of delay between "ticks" of the processing loop when the host is idle (i.e. not # processing traffic). (ms) [Note: Default value is recommend, normally this should not be changed.] idleTickDelay: 5 # Sets the local time offset from GMT. localTimeOffset: 0 # Flag indicating the watchdog overflow check should be disabled. disableWatchdogOverflow: false # # Location Information # (This is used mainly for reporting the location of the host to a connected network.) # info: # Latitude. latitude: -83.689428 # Longitude. longitude: -39.194973 # Height (in meters). height: 1 # Transmit Power (in watts). power: 10 # Textual location for this host. location: "Repeater Site, Antarctica" # # Site Configuration # config: # Flag indicating whether or not this host is authoritative (i.e. will automatically handle channel grant) for TGID operations. authoritative: true # Flag indicating whether or not this host acts as a supervisor (i.e. will automatically handle permission) for voice channel TGID permission. supervisor: false # Channel Identity (corresponds to the appropriate entry in the iden_table file). channelId: 2 # Channel Number (used to calculate actual host frequency based on the identity table). channelNo: 1 # # Control Channel # Note: These parameters are used by a voice channel to communicate back to a # control channel to give the control channel "real time" traffic channel updates. # These parameters should be left default for dedicated control channels. # controlCh: # REST API IP Address for control channel. (If blank, notifications are disabled.) restAddress: # REST API Port number for control channel. (If 0, notifications are disabled.) restPort: 0 # REST API access password for control channel. restPassword: "PASSWORD" # Flag indicating whether or not REST API is operating in SSL mode. restSsl: false # Flag indicating voice channels will notify the control channel of traffic status. notifyEnable: true # Amount of time between network presence announcements. (seconds) # NOTE: This value applies to VC -> CC and CC -> FNE presence notification messages. presence: 120 # # Voice Channels # voiceChNo: # Channel Identity (corresponds to the appropriate entry in the iden_table file). - channelId: 2 # Channel Number (used to calculate actual host frequency based on the identity table). channelNo: 1 # REST API IP Address for voice channel. restAddress: 127.0.0.1 # REST API Port number for voice channel. restPort: 9990 # REST API access password for voice channel. restPassword: "PASSWORD" # Flag indicating whether or not REST API is operating in SSL mode. restSsl: false secure: # AES-128 16-byte Key (used for LLA) # (This field *must* be 16 hex bytes in length or 32 characters # 0 - 9, A - F.) key: "000102030405060708090A0B0C0D0E0F" # DMR Color Code. colorCode: 1 # P25 Network Access Code (NAC). (Rx/Tx) nac: 293 # P25 Network Access Code (NAC). (Overrides the above for Tx when set.) # txNAC: 293 # NXDN Random Access Number. ran: 1 # Patch Super Group. pSuperGroup: FFFE # Announcment Talkgroup Group. announcementGroup: FFFE # DMR network ID. dmrNetId: 1 # P25 Network ID (WACN). netId: BB800 # P25/NXDN System ID. sysId: 001 # P25 RFSS (RF Sub-System) ID. rfssId: 1 # DMR/P25/NXDN Site ID. siteId: 1 # # CW ID Configuration # cwId: # Flag indicating whether or not CWID is enabled. enable: true # Amount of time between CWID transmissions. (minutes) time: 15 # Callsign to be transmitted. callsign: ABCD123 # # Modem Configuration # modem: # # Protocol Configuration # protocol: # Modem port type. # null - Null Modem (Loopback for testing) # uart - Serial Modem type: "null" # Valid values are "null", and "uart" # Modem interface mode. # air - Standard air interface modem (Hotspot or Repeater) # dfsi - TIA-102 DFSI interface modem mode: "air" # Valid values are "air", and "dfsi" uart: # UART/RS232 serial port device. port: /dev/ttyUSB0 # UART/RS232 serial port speed. (The default speed of 115200, should not be # changed unless the speed is also changed in the firmware of the modem.) speed: 115200 # Flag indicating whether or not the recieved signal is polarity inverted. rxInvert: false # Flag indicating whether or not the transmitted signal is polarity inverted. txInvert: false # Flag indicating whether or not the modem PTT signal should be active low. pttInvert: false # Flag indicating whether or not the modem DC noise blocker filter is enabled. dcBlocker: true # Flag indicating whether or not the modem COS signal should lockout transmit. cosLockout: false # Number of FDMA preambles to transmit before data. fdmaPreamble: 80 # Amount of time to wait before starting DMR transmissions after a signal is received. dmrRxDelay: 7 # Amount of packet correlations that should occur before P25 data is returned from the modem to the host. # (Note: Changing this value will impact P25 protocol stability, and should not be altered.) p25CorrCount: 8 # Size (in bytes) of the DMR transmit FIFO buffer. It is not recommended to adjust this unless absolutely # necessary, excessive sizes will cause delays in transmitted frames due to excessive buffering. # Calculation Formula: (DMR Frame Size (33 bytes) * x Frames) + Pad Bytes = FIFO Buffer Size Bytes # Default (Recommended) Value: (33 * 16) + 5 = 560 # "Oversized" Value: (33 * 24) + 5 = 797 dmrFifoLength: 560 # Size (in bytes) of the P25 transmit FIFO buffer. It is not recommended to adjust this unless absolutely # necessary, excessive sizes will cause delays in transmitted frames due to excessive buffering. # Calculation Formula: (P25 LDU Frame Size (216 bytes) * x Frames) + Pad Bytes = FIFO Buffer Size Bytes # Default (Recommended) Value: (216 * 2) + 90 = 522 # "Oversized" Value: (216 * 4) + 90 = 954 p25FifoLength: 522 # Size (in bytes) of the NXDN transmit FIFO buffer. It is not recommended to adjust this unless absolutely # necessary, excessive sizes will cause delays in transmitted frames due to excessive buffering. # Calculation Formula: (NXDN Frame Size (48 bytes) * x Frames) + Pad Bytes = FIFO Buffer Size Bytes # Default (Recommended) Value: (48 * 11) + 10 = 538 # "Oversized" Value: (48 * 19) + 10 = 922 nxdnFifoLength: 538 # # Hotspot Modem Configuration # hotspot: # DMR Discriminator Bandwidth Adjustment. dmrDiscBWAdj: 0 # Valid values between -128 and 128 # DMR Post Demodulator Bandwidth Adjustment. dmrPostBWAdj: 0 # Valid values between -128 and 128 # P25 Discriminator Bandwidth Adjustment. p25DiscBWAdj: 0 # Valid values between -128 and 128 # P25 Post Demodulator Bandwidth Adjustment. p25PostBWAdj: 0 # Valid values between -128 and 128 # NXDN Discriminator Bandwidth Adjustment. nxdnDiscBWAdj: 0 # Valid values between -128 and 128 # NXDN Post Demodulator Bandwidth Adjustment. nxdnPostBWAdj: 0 # Valid values between -128 and 128 # LNA Gain Mode. adfGainMode: 2 # 0 - Auto, 1 - Auto High Lin, 2 - Low, 3 - High # Flag indicating whether the ADF7021's automatic frequency correction is enabled. afcEnable: true # Don't change this. See the ADF7021 datasheet for more information. afcKI: 13 # Don't change this. See the ADF7021 datasheet for more information. afcKP: 5 # Sets the maximum frequency correction range of the ADF7021. # (It is highly recommended *not* to alter this.) afcRange: 1 # Sets the transmit frequency offset. (in Hz) txTuning: 0 # Sets the receive frequency offset. (in Hz) rxTuning: 0 # # Repeater Modem Configuration # repeater: # DMR +3/-3 symbol level adjustment. dmrSymLvl3Adj: 0 # Valid values between -128 and 128 # DMR +1/-1 symbol level adjustment. dmrSymLvl1Adj: 0 # Valid values between -128 and 128 # P25 +3/-3 symbol level adjustment. p25SymLvl3Adj: 0 # Valid values between -128 and 128 # P25 +1/-1 symbol level adjustment. p25SymLvl1Adj: 0 # Valid values between -128 and 128 # NXDN +3/-3 symbol level adjustment. nxdnSymLvl3Adj: 0 # Valid values between -128 and 128 # NXDN +1/-1 symbol level adjustment. nxdnSymLvl1Adj: 0 # Valid values between -128 and 128 # # (Optional) Software Potentiometer Configuration # [Note: This only applies to DVM board which include such support.] # softpot: rxCoarse: 127 # Valid values between 0 and 255 rxFine: 127 # Valid values between 0 and 255 txCoarse: 127 # Valid values between 0 and 255 txFine: 127 # Valid values between 0 and 255 rssiCoarse: 127 # Valid values between 0 and 255 rssiFine: 127 # Valid values between 0 and 255 # # V.24 Modem Configuration # dfsi: # RT/RT flag enabled (0x02) or disabled (0x04) rtrt: true # Use the DIU source flag (0x00) instead of the quantar source flag (0x02) diu: true # Jitter buffer length in ms jitter: 200 # Timer which will reset local/remote call flags if frames aren't received longer than this time in ms callTimeout: 200 # Flag indicating when operating in V.24 UDP mode, the FSC protocol should be used to negotiate connection. fsc: false # Sets the heartbeat interval for the FSC connection. fscHeartbeat: 5 # Flag indicating when operating in V.24 UDP mode, this instance should initiate the FSC protocol handshake. initiator: false # Flag indicating DFSI frames should be formatted in TIA-102 standard instead of serial standard format. dfsiTIAMode: false # Sets received the signal offset from DC. rxDCOffset: 0 # Valid values between -128 and 128 # Sets transmitted the signal offset from DC. txDCOffset: 0 # Valid values between -128 and 128 # Sets the received signal modulation level. rxLevel: 50 # Sets the transmitted signal modulation level. txLevel: 50 # Sets the transmitted CWID signal modulation level. # cwIdTxLevel: 50 # Sets the transmitted DMR signal modulation level. # dmrTxLevel: 50 # Sets the transmitted P25 signal modulation level. # p25TxLevel: 50 # Sets the transmitted NXDN signal modulation level. # nxdnTxLevel: 50 rssiMappingFile: RSSI.dat # Deprecated. Sets the playout time in seconds between sending buffered data to the modem. packetPlayoutTime: 10 # Flag indicating that modem resets due to ADC or DAC overflows is disabled. disableOFlowReset: false # Flag indicating that the modem configuration area data should be ignored. ignoreModemConfigArea: false # Flag indicating whether verbose dumping of the modem status is enabled. dumpModemStatus: false # Flag indicating whether or not trace logging is enabled. trace: false # Flag indicating whether or not debug logging is enabled. debug: false # # Channel Identity Table Configuration # iden_table: # Full path to the identity table file. file: iden_table.dat # Amount of time between updates of identity table file. (minutes) time: 30 # # Radio ID ACL Configuration # radio_id: # Full path to the RID ACL file. file: rid_acl.dat # Amount of time between updates of RID ACL file. (minutes) # NOTE: If utilizing purely FNE pushed RID ACL rules, this update time should be set to 0 to prevent # FNE rules from becoming erased. time: 2 # Flag indicating whether or not RID ACLs are enforced. acl: false # # Talkgroupd ID ACL Configuration # talkgroup_id: # Full path to the talkgroup rules file. file: talkgroup_rules.yml # Amount of time between updates of talkgroup rules file. (minutes) # NOTE: If utilizing purely FNE pushed talkgroup rules, this update time should be set to 0 to prevent # FNE rules from becoming erased. time: 2 # Flag indicating whether or not TGID ACLs are enforced. acl: false